Rice Lake iRev 920i Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 101

Rice Lake iRev 920i Скачать руководство пользователя страница 39

Configuration

35

3.2.7

Analog Output Menu

The ALGOUT menu is shown only if the analog output option is installed. If the analog output option is
installed, conÞgure all other indicator functions and calibrate the indicator itself before conÞguring the analog
o u t p u t

Figure 3-12. Analog Output Menu

3.2.8

Version Menu

The VERS menu can be used to check the installed software version or, by using the

Reset Config

softkey, to

restore all conÞguration parameters to their factory default values. There are no parameters associated with the
Version menu: when selected, the indicator displays the installed software version number.

Figure 3-13. Version Menu

ALG OUT Menu

Parameter

Choices

Description

Level 2 submenus

SOURCE1

PROG

SCALE

n

Specifies the scale tracked by the analog output. PROG indicates that the analog output is under
program control.

MODE1

GROSS

NET

Specifies the weight data, gross or net, tracked by the analog output.

OFFSET

0%

20%

Zero offset. Select 0% for 0–10 V or 0–20 mA output; select 20% for 4–20 mA output. This
parameter must be set before calibrating the analog output.

ERRACT

FULLSC

HOLD
ZEROSC

Error action. Specifies how the analog output responds to system error conditions.
Possible values are:

FULLSC: Set to full value (10 V or 20 mA)
HOLD: Hold current value
ZEROSC: Set to zero value (0 V or 4 mA)

MIN

000000

0–9999999

Specifies the minimum weight value tracked by the analog output. Specify a value in the range
0–9999999.

MAX

010000

0–9999999

Specifies the maximum weight value tracked by the analog output. Specify a value in the range
0–9999999

TWZERO

40

0–65535

Tweak zero. Enter tweak value to adjust the analog output zero calibration. Use a multimeter to
monitor the analog output value.

TWSPAN

59650

0-65535

Tweak span. Enter tweak value to adjust the analog output span calibration. Use a multimeter to
monitor the analog output value.

Table 3-8. Analog Output Menu Parameters

SCALES

SERIAL

FEATURE

PFORMT

SETPTS

DIG I/O

ALGOUT

VERS

number

40

number

SOURCE1

PROG

OFFSET

20%

0%

ERRACT

SCALE

n

FULLSC

HOLD

ZEROSC

MIN

number

000000

MAX

number

10000

TWZERO

59650

TWSPAN

MODE1

GROSS

NET

If SOURCE1

¹

PROG

SCALES

SERIAL

FEATURE

PFORMT

SETPTS

DIG I/O

ALGOUT

VERS

Software

version

«
...
37
38
39
40
41
...
»

Содержание iRev 920i






































































































Отзывы:

Нет отзывов