manualshive.com logo in svg

Rice Lake 482-AG, Техническое руководство

Поделиться
Скачать
Rice Lake 482-AG Скачать руководство пользователя страница 5

Introduction

© Rice Lake Weighing Systems

 

●

 All Rights Reserved

1

1.0

Introduction

This manual is intended for use by service technicians responsible for installing and servicing 482-AG digital weight indicators. 

Manuals and additional resources are available from the Rice Lake Weighing Systems website at 

www.ricelake.com

Warranty information can be found on the website at 

www.ricelake.com/warranties

1.1 Safety

Safety Signal Definitions:

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes 

hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes 

hazards that are exposed when guards are removed.

  Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.

Indicates information about procedures that, if not observed, could result in damage to equipment or corruption 

to and loss of data.

General Safety

Do not operate or work on this equipment unless this manual has been read and all instructions are understood. 

Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake 

Weighing Systems dealer for replacement manuals. 

Failure to heed could result in serious injury or death.

Some procedures described in this manual require work inside the indicator enclosure. These procedures are to be performed by 

qualified service personnel only.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not operate without the enclosure completely assembled.
Do not use for purposes other than weight taking.
Do not place fingers into slots or possible pinch points.
Do not use this product if any of the components are cracked.
Do not exceed the rated specification of the unit, see 

Section 9.0 on page 53

.

Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Do not submerge.
Before opening the unit, ensure the power cord is disconnected from the outlet.

DANGER

WARNING

CAUTION

IMPORTANT

WARNING

Содержание 482-AG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды