manualshive.com logo in svg

Rice Lake 482-AG, Техническое руководство

Поделиться
Скачать
Rice Lake 482-AG Скачать руководство пользователя страница 10

482-AG Livestock Digital Weight Indicator

6

Visit our website 

www.RiceLake.com

1.7.1 Numeric Keypad - Editing Procedure for Numeric Values (482 Plus Only)

Figure 1-6. Numeric Keypad for the 482-AG

  With the numeric keypad, numbers can be edited using the keypad in addition to the arrow method.

1. When editing numeric values, insert the required value using the numeric keypad.

i. Press 

 to set the currently selected digit to 0

ii. Press 

 to enter a decimal point

2. Press 

 to save the value entered and return to the level above.

When editing fractional numeric values, the decimal point must be positioned in accordance with the primary units 

formatting, otherwise the keyed number may be rejected by the software.

1.8 Indicator Operations

Basic operations for the 482-AG are summarized below.

1.8.1 Zero Scale

1. Remove all weight from the scale and wait for the 

 annunciator to light.

2. Press 

. The 

 annunciator lights to indicate the scale is zeroed.

1.8.2 Toggle Units

Press 

 to toggle between primary and secondary units. The current unit annunciator is displayed.

  Units cannot be changed once a group weighment has been started.

1.8.3 Print Ticket

The print key sends the group data to the serial port. This key will also reprint a group ticket for the current group data on the 

indicator. For more information on print formatting, see 

Section 7.0 on page 46

.

1. Wait for 

 annunciator to display.

2. Press 

 to send data to the serial port.

If the 

 key is pressed when the 

 is not displayed, unless the scale stabilizes withing three seconds, 

the print command is ignored.

1.8.4 Shrink Factor

The shrink factor limits are 0.0% to 99.0%. The default is 0.0%. In the weigh mode, enter the shrink factor on the numeric 
keypad and press 

. The entered shrink factor is applied to every weighment until the shrink factor is changed or the 

indicator is reset. A shrink factor, however, can be entered at any time, but only the last shrink factor prior to pressing 

 

will be applied to all of the groups making up the load. The shrink factor is not displayed when weighing, however, the shrink 

factor value and results are printed on the load total ticket only. The entered shrink factor is stored and will survive power 

cycles.

Note

Note

Note

Note

Содержание 482-AG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды