Ricatech Ibiza RMC90, Инструкция по эксплуатации, Страница: 4 / 91

4
6.
SETTING ALARM IS COMPLETED, THE DISPLAY WILL SHOW THE SETTING AGAIN FOR USER’S
CHECKING
7. “CLOCK” ICON IS FLASHING WHEN ALARM IS IN ACTIVE. “CLOCK” ICON LIGHTS UP WHEN ALARM IS
SETTING IS STORED BUT NOT IN ACTIVE YET.
8. CANCEL ALARM: DURING STANDBY MODE, WHEN “CLOCK” ICON IS ON, PRESS TIMER BUTTON ,
“CLOCK” ICON WILL BE OFF.
SNOOZE FUNCTION
PRESS “SNOOZE” BUTTON ON THE REMOTE CONTROL WHEN ALARM IN ACTIVE, ALARM WILL BE SLIENT
FOR 10 MINUTES. AFTER 9-10 MINUTUE SNOOZE INTERVAL, ALARM WILL BE ACTIVE AGAIN. SNOOZE CAN
BE USED FOR REPEATEDLY WITHIN THE 1-HOUR ALARM ACTIVE INTERVAL.
TIMER FUNCTION
1. PUSH THE
POWER KNOB
TILL THE
STANDBY INDICATOR
LIGHT OFF. UNIT IS TURNING FROM STANDBY
MODE TO OPERATION MODE.
2. WHEN THE UNIT IS TURNED ON, PRESS
SLEEP
BUTTON REPEATEDLY TO CHOOSE THE SLEEP TIME
MINUTES FROM 90>80>703..>10 OFF.
3. SLEEP TIME SETTING IS STORED WHEN THE “SLEEP” ICON LIGHTS UP ON THE DISPLAY.
4. WHEN THE SLEEP TIME MINUTES IS OVER, UNIT WILL BE SWITCHED TO STANDBY MODE
AUTOMATICALLY.
LISTENING TO RADIO
RADIO TUNING
1. PRESS TUNER BUTTON TO ACTIVATE “TUNE” MODE.
2. SELECT THE DESIRED BAND BY RADIO TUNRER BUTTON (AM OR FM) AGAIN.
3. TUNE TO THE REQUIRED STATION BY TURNING TUNING KNOB UPWARDS OR BACKWARDS FOR 1-2
SECONDS, AND THEN RELEASE.
4. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP WHEN A RADIO STATION IS FOUND.
MANUAL PRESET RADIO STATIONS
1. WHEN THE DESIRED RADIO STATION IS FOUND, PRESS MODE BUTTON, PROGRAM NUMBER WILL BE
FLASHING.
2. PRESS PRESET UP OR PRESET DOWN TO CHOOSE THE PROGRAM NUMBER FOR STORING THE
DESIRED RADIO STATION.
3. PRESS MODE BUTTON AGAIN TO CONFIRM, PROGRAM NUMBER WILL STOP TO FLASH.
4. REPEAT STEP 2 & 3 UNTIL ALL DESIRED RADIO STATIONS IS BEING FOUND AND STORED
5. PRESS PRESET UP OR PRESET DOWN TO CHOOSE THE PRESET RADIO STATIONS.
6. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
AUTO PRESET RADIO STATIONS
1. DURING RADIO MODE, PRESS THE SCAN BUTTON, THE UNIT WILL AUTOMATICLLY SCAN THE RADIO
FREQUENCY. WHEN THE CLEAR SIGNAL IS FOUND, IT WILL AUTOMATICALLY STORE THE RADIO
STATION, STARTING FROM PROGRAM NUMBER 1.
2. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
FM & FM-STEREO RECEPTION
PRESS “FM ST.” BUTTON ON THE REMOTE CONTROL TO SELTECT FM MONO OR FM STEREO MODE.
WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO.
“ST” ICON LIGHT UP ON THE DISPLAY TO SHOW FM STEREO MODE IS RECEIVING.
HINTS FOR BETTER RECEPTIO
1. AM: THERE IS A BUILT-IN AM BAR ANTENNA. IF AM RECECPTION IS WEAK, SLIGHTLY ROTATING OR
RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
2. FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RADIO ENCODING
1. PRESS TUNER BUTTON TO ACTIVATE “TUNE” MODE AND SELECT THE DESIRED BAND BY RADIO BAND
BUTTON (AM OR FM).
2. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)
3. PRESS THE REC BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD
ICON WILL BE FLASHING.