Rheem Solar Hiline 52D180 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 56

Rheem Solar Hiline 52D180 Скачать руководство пользователя страница 20

INSTALLATION – SOLAR STORAGE TANK

20

SOLAR WATER HEATER STORAGE TANK LOCATION

The solar storage tank is designed to be installed on the roof directly coupled to the solar collectors. The solar
water heater should be installed close to either the most frequently used outlet or the previously installed water
heater in a retrofit installation if existing pipe work is to be utilised, and its position chosen with safety and
service in mind. The solar water heater should be installed with as close to a north facing aspect as possible
(refer to

“Solar Collector Location”

on page 27). The solar storage tank should not be installed inside the roof

space.

The  solar  collectors  must  not  be  installed  with  an  inclination  of  less  than  10°,  otherwise  the  water  will  not
thermosiphon efficiently through the collectors.

Clearance  must  be  allowed  for  servicing  of  the  solar  storage  tank.
Make sure the temperature pressure relief valve lever is accessible
and  the  side  cover,  thermostat  and  booster  heating  unit  can  be
removed for service. You must be able to read the information on the
rating plate. If possible leave side room of one water heater length so
the anode can be inspected or replaced.

Remember  you  may  have  to  remove  the  entire  solar  storage  tank
later for servicing. The solar storage tank must be capable of being
removed  without  structural  alteration  to  the  building  or  major
alteration to the piping.

For  a  single  water  heater  installation,  refer  to  the

to

26. For multiple water heater installations, also refer to

instructions on page

The solar storage tank must be installed horizontally level. Remember all local authorities have regulations
about putting water heaters into roof spaces.

MAINS WATER SUPPLY

Where the mains water supply pressure exceeds that shown in the table below, an approved pressure limiting
valve is required and should be fitted as shown in the

cold water connection detail on page

Model

180, 300

Relief valve setting

1000 kPa

Expansion control valve setting *

850 kPa

Max. mains supply pressure

With expansion control valve

680 kPa

Without expansion control valve

800 kPa

* Expansion control valve not supplied with the water heater

TANK WATER SUPPLY

If the water heater is supplied with water from a tank supply and a pressure pump system is not installed, then
the bottom of the supply tank must be at least one (1) m above the highest point of the hot water plumbing
system, including the water heater. Care must be taken to avoid air locks. The cold water line to the water
heater should be adequately sized and fitted with a full flow gate valve or ball valve.

«
...
18
19
20
21
22
...
»

Содержание Solar Hiline 52D180

























































Отзывы:

Нет отзывов