Rheem Multipak MPE02 Скачать руководство пользователя

Страница: 56 / 60

COMMISSIONING

MULTIPAK – OPTIONAL CIRCULATING PUMP SUCTION STRAINER CLEANING

Turn Off the power supply to the circulating pump. Isolate the pump upstream valve.

Remove the pump upstream strainer assembly. Clean and refit.

Re-instate the pump upstream valves to open position.

Follow the secondary pump commissioning start-up instructions 7, 8 and 9 as stated before.

Re-instate the pump power supply.

Basic Instruction for inline wet rotor Circulating Pump;

Motor shaft shall be Horizontal. Never operate dry. Loop cable down on exiting

terminal box as shown. Bleed pump; Confirm rotation. Free shaft assembly, if

necessary; Power supply timer is required to turn off pump automatically at least

four (4) times daily for 5 minutes; Clean pump suction strainer regularly.

Pump Upstream

Isolation Valve

Check Valve

Strainer

Содержание Multipak MPE02





























































Результаты поиска

Содержание Multipak MPE02

Отзывы:

Похожие инструкции для Multipak MPE02

Бренды по названию

Популярные бренды

Rheem Multipak MPE02, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание Multipak MPE02

Отзывы:

Похожие инструкции для Multipak MPE02

Бренды по названию

Популярные бренды