Rheem 834 Series Скачать руководство пользователя страница 51

Страница: 51 / 61

TM081 Rheem 834 Series Hydroelectric CFGWH Service Instructions
REV: AA Issued: 22/02/17

This document is stored and maintained electronically by Rheem Technical Support. All printed copies are deemed uncontrolled.

Battery (Procedure 3)

1. Remove battery by performing steps 1 ~ 4 of procedure 2.

2. Reassemble in reverse order of above ensuring positive (+) end of battery is in down

position.

Ignition Module (Procedure 4)

Note:

The ignition rod and flame sensor leads are supplied adhered to the ignition module

and should not be removed.

Isolate water supply to heater by closing cold water inlet isolation valve located
below heater.

2. Remove front panel by following steps 1 ~ 2 of procedure 1.

3. Disconnect high tension lead from ignition rod by pulling lead away from ignition rod.

4. Disconnect high tension lead from flame sensor by pulling lead away from flame

sensor.

5. Remove single Phillips head screw retaining ignition module mounting bracket to heat

shield, push front of bracket to the right and slide bracket complete with ignition
module out of heat shield.

6. Unplug wiring plug from ignition module.

7. Remove two Phillips head screws retaining ignition module to ignition module

mounting bracket and remove ignition module from bracket.

8. Reassemble in reverse order of above.

Note:

When reconnecting ignition module

leads, ensure top ignition module lead connects to ignition rod and bottom ignition
module lead connects to flame rod.

Pilot Assembly (Procedure 5)

The pilot assembly is comprised of pilot injector, pilot, ignition rod, flame sensor and
mounting bracket. Note: To only remove pilot injector, refer to procedure 6.

Isolate water supply to heater by closing cold water inlet isolation valve located
below heater.

Isolate gas supply to heater by closing gas isolation valve located below heater.

3. Remove front panel by following steps 1 ~ 2 of procedure 1.

4. Remove two Phillips head screws retaining pilot shield and remove pilot shield.

5. Disconnect high tension lead from ignition rod by pulling lead away from ignition rod.

6. Disconnect high tension lead from flame sensor by pulling lead away from flame

sensor.

7. Using a 9 mm spanner, hold pilot injector and remove pilot feed pipe olive using an 8

mm spanner.

8. Gently pull pilot feed pipe out from pilot assembly.

9. Remove two Phillips head screws retaining pilot assembly mounting bracket and

remove pilot assembly complete with mounting bracket and metal spacer.

10. Reassemble in reverse order of above.

Note:

When reconnecting ignition module

leads, ensure top ignition module lead connects to ignition rod and bottom ignition
module lead connects to flame rod.

11. Start heater and check for gas leaks using a soapy water solution.

Содержание 834 Series






























































Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды

Rheem 834 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды