background image

9912 

 

H.

 

PROCEDURE FOR WARRANTY PERFORMANCE 

 
If the product fails to perform to the Manufacturer’s specifications, the Buyer must provide the Manufacturer with the 
applicable model and serial numbers, the date of purchase, and the nature of the problem. 
 

I.

 

ADDITIONAL EXCLUSIONS FROM THIS LIMITED WARRANTY.  THIS LIMITED WARRANTY 

DOES NOT COVER ANY OF THE FOLLOWING: 

 
1.

 

Equipment which has been abused, damaged, used beyond rated capacity, or repaired by persons other than 
authorized service personnel. 

 
2.

 

Damage caused by acts of God which include, but are not limited to, hailstorms, windstorms, tornadoes, sandstorms, 
lightning, floods, and earthquakes. 

 
3.

 

Damage under conditions caused by fire or accident, by abuse or by negligence of the user or any other person other 
than the Manufacturer, by improper installation, by misuse, by incorrect operation, by “normal wear and tear”, by 
improper adjustment or alteration, by alterations not completed by authorized service personnel, or by failure of 
product parts from such alterations. 

 
4.

 

Costs of repairing damage caused by poor or improper maintenance, costs of normally scheduled maintenance, or the 
cost of replacing any parts unless done as the result of an authorized repair covered by the one (1) year Limited 
Warranty. 

 
5.

 

Costs of modifying the product in any way once delivered to the Buyer, even if such modifications were added as a 
production change on other products made after the Buyer’s product was built. 

 

J.

 

NO AUTHORITY TO ALTER THIS LIMITED WARRANTY 

 
No agent, representative, or distributor of the Manufacturer has any authority to alter the terms of this Limited Warranty 
in any way. 
 

 

 
 
 
 

 
 

Содержание TS14



















Отзывы: