background image

602400011500 

Revision C 

Page 

7

 of 

24  

 

3

 

TERMS

 

&

 

DEFINITIONS

 

3.1

 

Relative

 

Humidity

 

(RH)

  is  the  moisture 

content of the air relative to the maximum 

possible  moisture  content  at  the  current 
air  temperature.  RH  is  measured  in 

percent  (%).  100%  RH  represents 
saturation,  and  is  the  point  at  which 

condensation occurs. 
Since  RH  is  relative  to  temperature,  the 

RH  of  the  air  in  the  waveguide  or  cable 
will  fluxuate  with  the  changes  in  air 

temperature.  As  the  air  temperature 
increases,  RH  will  fall;  as  the  air 

temperature  decreases,  the  RH  will  rise. 
The air’s actual moisture content remains 

constant. 

3.2

 

Dew

 

Point

 

Temperature

 

(Td)

  is  the 

temperature  at  or  below  the  current 
temperature  at  which  the  air  would  be 

saturated with moisture (100% RH). Td is 
measured  in  the  same  unit  as  ambient 

temperature,  typically  Fahrenheit  or 

Celsius. 
Dew  point  temperature  is  not  affected  by 

air  temperature  fluxuations.  Instead,  it  is 
directly  linked  to  the  actual  moisture 

content  in  the  air.  For  that  reason,  dew 
point  temperature  is  the  measurement 

most  applicable  to  dehumidification 
processes. 
Dew  point  temperature  is  fairly  constant 
over  time.  Weather  systems  and  seasonal 

changes  are  the  primary  cause  of  dew 
point temperature fluxuation over time. 
When  dew  point  temperature  and 
ambient  air  temperature  are  equal,  then 

the  air  is  saturated  (100%  RH),  and 
condensation  can  form.  Therefore,  it  is 

important  to  keep  the  dew  point 
temperature  of  the  air  inside  the 

waveguide  or  cable  below  the  ambient 

temperature  outside  the  waveguide  or 
cable to avoid condensation. 

3.3

 

Dew

 

Point

 

Reduction

 

(Tdr)

  is  the 

reduction  of  the  dew  point  temperature 
that  results  from  the  dehumidification 

process.  The  larger  the  Tdr,  the  more 
efficient the dehumidification process is. 

3.4

 

Distribution

 

System

  is  the  system  of  air 

tubes,  distribution  manifolds,  valves,  and 

RF  lines  to  be  pressurized  with  dry  air 
from the dehydrator’s output fitting. 

3.5

 

Active

  dehydrator  operation  is  when  the 

unit’s  compressor  is  on  and  pressurized 

dry  air  is  being  supplied  from  the  unit’s 
output fitting. 

3.6

 

Run

 

Time

 is the time that the unit spends 

in  active  operation  to  pressurize  the 

distribution system. 

3.7

 

Standby

  dehydrator  operation  is  when 

the unit is energized but the compressor is 
not  on.  The  distribution  system  pressure 

is  in  the  unit’s  configured  operational 

range, and is being monitored by the unit’s 
control  board.  This  is  the  predominant 

operational condition. 

3.8

 

Duty

 

Cycle

 is the time in active operation 

vs.  standby  operation,  measured  in 
percent. 

 

 

 % =  

   100 

3.9

 

Lower

 

Operational

 

Pressure

 

(LOP)

  is 

the  configured  pressure  at  which  the 

dehydrator  will  switch  from  standby  to 
active  operation  to  re-pressurize  the 

system. 

3.10

 

Upper

 

Operational

 

Pressure

 

(UOP)

  is 

the  configured  pressure  in  psig  at  which 
the  dehydrator  will  switch  from  active  to 

standby operation. This is also the system 
pressure,  or  the  maximum  pressure 

desired in the distribution system. 

 

Содержание APD-D Series

























Отзывы: