background image

2. Connecting Alarm Relays and Power 

 
The following section describes how to connect Alarm Relays and Power to the eXmux 3500M. 
 
Before beginning the installation note the following: 
 

 

RFL recommends that wires only be terminated with ring lugs. 

 

 

The specified operating temperature of the eXmux 3500M is -30

°

C  to +65

°

C  

(-22

°

F to +149

°

F).  Operation at higher temperatures may affect system reliability and 

performance.  Systems installed in enclosed cabinets should be well ventilated.  

A full 1U of 

chassis space must be left open above the installed eXmux 3500M. 

 

 

Before proceeding with the connection of power to the eXmux 3500 ensure that the main and 
redundant power supply switches are in the “OFF” position, and that the power wires to be 
installed are disconnected at their source. 

 

 

All relay contacts are labeled in the de-energized position. 

 

 

Ensure that the power supply(ies) installed in your eXmux 3500M will operate at the 
available input power. 

 

 

Follow all of your company’s policies and procedures regarding the installation of AC powered 
or DC powered equipment.  If there is a conflict between any procedure in this Quick Start 
Guide and your company’s safety rules, then your company’s safety rules must take priority. 

 

 

CAUTION 

Any installation using an enclosed cabinet with a swing-out rack must be securely fastened to the 
floor.  This will prevent the cabinet from falling forward when the rack is moved outward. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

E

X

MUX 3500M Quick Start

 

 

RFL Electronics Inc. 

January 23, 2013 

                         2 

973.334.3100 

Содержание eXmux 3500





















Отзывы: