background image

AIR SUPPLY

Check that supply air pressures and flow are
adequate to supply system. Check height con-
trol valve and linkages to ensure unit is operat-
ing at correct ride height. 

AIR SPRINGS

The air springs are equipped with internal bump
stops for safety. However, do not operate the
loaded unit on the bump stops for any extend-
ed periods of time, except to move the unit to a
repair facility.

Please ensure that you are matching the correct
air spring to the suspension model.

TORQUE

To comply with warranty and safety require-
ments, check torque values during pre-delivery
inspection, after 1,600 kms (1,000 miles) of
operation and each additional 80,000 kms
(50,000 miles) or annually, whichever is first.

M-3

PERSONAL LIFTING

Practice safe lifting procedures.  Consider size,
shape, and weight of assemblies. Obtain help
or the  assistance of a crane when lifting heavy
assemblies. Make sure the path of travel is
clear.

OVERLOADING

Overloading of the suspension system or its
components is the practice of transporting car-
gos that surpass the specified vehicle’s ratings.
Overloading can cause component failure,
resulting in accidents and injuries.

Torque Wrench

Normal Operation Air Spring

Under-Inflated Air Spring

Filter

Pressure 

Protection Valve

Height
Control
Valve

Left Side

Air Springs

Link

Right Side

Air Springs

Mounting

Bracket

Air Supply

Compatible Model: Proto, Model #6020

(call factory for details)

Содержание 23AR



















Отзывы: