REXROTH IndraDrive Скачать руководство пользователя страница 219

Страница: 219 / 312

Cooling Unit on Top of the Control Cabinet

Cooling Unit at the Front of the Control Cabinet

Cooling unit

Interior of control cabinet

Air duct (protects devices against condensation water)

Device in control cabinet

Tab.12-2:

Arranging the Cooling Units

Avoiding Moisture Condensation

Moisture condensation occurs when the temperature of the device is lower

than the ambient temperature.
●

Set cooling units with temperature adjustment to the maximum sur‐

rounding temperature and not lower!

●

Set cooling units with follow-up temperature in such a way that the inte‐

rior temperature of the control cabinet is not lower than the temperature

of the surrounding air. Set the temperature limitation to the maximum

surrounding temperature!

●

Only use well-sealed control cabinets so that moisture condensation

cannot arise as a result of warm and moist external air entering the cabi‐

net.

●

In the event that control cabinets are operated with the doors open

(commissioning, servicing etc.), it is essential to ensure that after the

doors are closed the drive controllers cannot at any time be cooler than

the air in the control cabinet. For this reason, sufficient circulation must

be provided inside the control cabinet.

DOK-INDRV*-SYSTEM*****-PR06-EN-P
Rexroth IndraDrive Drive Systems with HMV01/02 HMS01/02, HMD01, HCS02/03

Bosch Rexroth AG

217/309

Project Planning of Cooling System

Содержание IndraDrive

























































































































































































































































































































Результаты поиска

Содержание IndraDrive

Отзывы:

Похожие инструкции для IndraDrive

Бренды по названию

Популярные бренды

REXROTH IndraDrive, Руководство по планированию проекта

Результаты поиска

Содержание IndraDrive

Отзывы:

Похожие инструкции для IndraDrive

Бренды по названию

Популярные бренды