Rexnord Planetgear 7000 Скачать руководство пользователя страница 5

Страница: 5 / 33

Owners Manual • Rexnord

Planetgear

™

7000 Speed Reducers

(Page 5 of 33)

Size Mercury/Mars

158-110

10/21 (Supersedes 01/15)

rexnord.com

rexnord.com/contact

2.3.1b. MOTORS (C-FACE & IEC MOTOR

FLANGE UNITS)

1. Mount the reducer C-face coupling or IEC motor flange

coupling onto the motor shaft with the appropriate size

key. The motor shaft to coupling fit should be snug

and may require light tapping (Note: Warming up the

coupling and applying an Anti-seize compound to

the motor shaft is helpful). Note: A loose fit coupling

should be avoided and a heavy fit could damage motor

bearings if the coupling is pressed onto the motor shaft

with extreme force.

CAUTION

: Never turn down the motor shaft diameter

to allow for easy coupling installation, as this will cause

coupling movement and wear during operation.

2.a. C-FACE: Locate the C-Face coupling 0.688 to 0.750” from

the motor face (Hint: Standard keystock is helpful for this

purpose). Refer to the illustration in

Figure 2.3.1 b

2.b. IEC MOTOR FLANGE COUPLING: Locate the coupling

13.0 to 14.0mm from the motor face. Refer to the

illustration in

Figure 2.3.1 c

3. Tighten the coupling set screws; one located over

the key and the other located at 90° (degrees). After

tightening the set screws, the gap between the motor

face and the coupling should be measured again to

insure that the tolerance has been maintained. If the

tolerance is not within the specification, loosen the set

screws and repeat steps 2 and 3.

4. Mount the motor with coupling to the reducer. Align the

internal spline end of the coupling with the external

spline end of the reducer input gear.

CAUTION

: Be careful not to roll the seal when installing

or removing the coupling and motor. This could result in

oil leakage during operation.

5. Align the mounting holes of the motor with the mounting

holes of the reducer, and fasten, reference

Table 18

(Page 29) for recommended bolt torques.

SETSCREWS

C-FACE COUPLING

REDUCER

INPUT GEAR

DOUBLE

LIPPED

SEAL

0.688”/0.750”

HOLD DIMENSION WHEN

MOUNTING INPUT COUPLING

TO MOTOR SHAFT

Figure 2.3.1b C-Face Cross Section

13mm/14mm

HOLD DIMENSION WHEN

MOUNTING COUPLING

TO MOTOR SHAFT

DOUBLE

LIPPED

SEAL

REDUCER

INPUT GEAR

SETSCREWS

IEC MOTOR FLANGE COUPLING

Figure 2.3.1c IEC Cross Section

2.3.2 COUPLINGS

Mount the reducer coupling hub on the input shaft and the

motor coupling hub on the motor shaft as instructed in the

manual shipped with the coupling. If the coupling is not

a Rexnord

Omega

, refer to the manufacturers literature

for installation instructions. If Rexnord does not mount

the motor, the couplings are mounted for shipment only.

Coupling bolts and coupling instructions are packed inside

the coupling elements. Note: Prior to the installation of the

element, check both coupling hubs for the required parallel

and angular alignment; Reference

Figure 2.3.2

PARALLEL MISALIGNMENT

ANGULAR MISALIGNMENT

Figure 2.3.2 Parallel and Angular Misalignment

2.3.3 SPROCKETS OR SHEAVES

Prior to installing sprockets or sheaves, review the

manufacturers requirements for chain or belt tension and

required alignment. When mounting the sprocket or sheave to

the shaft, locate it as close as possible to the reducer. This will

minimize the overhung load and prolong bearing life.
When using a Planetgear 7000 top motor mount accessory,

the belt tension can be changed by varying the height of

the motor mount plate. This can be done by adjusting the

four threaded support bolts. Reference

Figure 2.3.3

NOTE

: Mount sheaves and belts as close to the reducer as

possible to avoid undue overhung loading on the bearings.

MOTOR

THREADED

SUPPORT

BOLTS

REDUCER

GUARD

REDUCER

FAN/SHROUD

Figure 2.3.3 Planetgear Top Motor Mount

Содержание Planetgear 7000


































Результаты поиска

Содержание Planetgear 7000

Отзывы:

Бренды по названию

Популярные бренды

Rexnord Planetgear 7000, Руководство пользователя

Результаты поиска

Содержание Planetgear 7000

Отзывы:

Бренды по названию

Популярные бренды