manualshive.com logo in svg

REWIRE SECURITY DB3, Руководство пользователя, Страница: 9 / 122

Поделиться
Скачать
REWIRE SECURITY DB3 Скачать руководство пользователя страница 9

1.2

 

Safety Instructions 

 

This chapter contains information on how to operate DB3 Plug&Play safely. 
By  following  these  requirements  and  recommendations,  you  will  avoid 
dangerous situations. You must read these instructions carefully and follow 
them strictly before operating the device!  
The device uses a 10 V...16 V DC power supply. The nominal voltage is 12 V 
DC. The allowed range of voltage is 10 V...16 V DC.  
To avoid mechanical damage, it is advised to transport the DB3 Plug&Play 
device in an impact-proof package.  
Before dismounting the device from the vehicle, the ignition must be off. 

  

1.3

 

Legal Notice  

 

Copyright  ©  2015  Rewire  Security.  All  rights  reserved.  Reproduction, 
transfer,  distribution  or  storage  of  part  or  all  of  the  contents  of  this 
document  in  any  form  without  the  prior  written  permission  of  Rewire 
Security is prohibited.   
Other products and company names mentioned here may be trademarks 
or trade names of their respective owners.  
The  manufacturer  reserves  the  right  to  make  changes  and/or 
improvements  at  any  time  in  design,  functionality,  parameters  and 
electrical  characteristics  without  any  prior  notice  and  without  incurring 
obligations.  

1.4

 

About Document  

 

This document contains information about the architecture, possibilities, 
mechanical characteristics, and configuration of the DB3 Plug&Play device. 
Acronyms and terms used in document PC – Personal Computer.  

GPRS

 – General Packet Radio Service  

GPS

 – Global Positioning System  

GNSS

 

– 

Global Navigation Satellite System

 

 

GSM

 – Global System for Mobile Communications  

SMS

 – Short Message Service  

AC/DC

 – Alternating Current/Direct Current  

I/O

 – Input/Output  

Содержание DB3



























































































































Отзывы:

Нет отзывов