REWIRE SECURITY DB3 Скачать руководство пользователя страница 58

Страница: 58 / 122

129 “Fuel consumption (averaged)” 0

65535 L/100km 2B X0.01

Table 4 OBD IO list

Note

: Available OBD elements depend on vehicle’s brand, model

and year of manufacturing. More information on OBD PIDs:

http://en.wikipedia.org/wiki/OBD-II_PIDs

5.13.3 Fuel Consumption Calculation

If data from OBD is not available (PID 94), DB3 Plug&Play can do calculations
with other OBD parameters: Speed, Throttle, MAF, MAP, RPM, Engine Load.
Calculation method can be configured:

Figure 34 Fuel consumption on configurator window

Auto

– DB3 Plug&Play independently decides how to calculate fuel

consumption depending on PIDs availability and configured fuel type.

From PID

– no calculations are established. Fuel value is taken from the vehicle.

Calculate from OBD data

– same as

Auto

, but does not use PID 94 if it is

available from OBD data.

Calculated by norm value

– not implemented yet.

Fuel Type

– vehicle fuel type: Gasoline; Diesel or LPG.

Engine Volume

– set vehicle fuel volume.

Correction

– this parameter gives ability to correct the calculated fuel value

and adopt it to specific vehicle. Correction is multiplication coefficient. Here are
some fuel calculation correction examples:

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 58 / 122

Результаты поиска

Содержание DB3

Отзывы: