REWIRE SECURITY DB3 Скачать руководство пользователя страница 45

Страница: 45 / 122

Figure 22 Scenarios configuration

Green Driving

: Eventual Record is generated when driving over allowed

(configured) parameters.

Over Speeding:

Eventual Record is generated when driving over allowed

(configured) speed and returning to normal speed.

Excessive Idling Detection:

If the ignition is ON and no movement, the event

will be generated when TMO reached. The user can enable this functionality,
select timeouts for stationary time and for movement time.

Jamming Detection

: User can select Jamming detection sensitivity (RSSI

threshold): Low, Normal, High and Disable this functionality.

5.11.2 Trip Settings

If OBD data and PIDs are available, odometer value will be calculated from
OBD, if not – from GPS.

The trip window offers the user to configure Trip feature. If Trip is enabled
configuration of parameters are enabled.

Start Speed

– GNSS speed has to be greater than the specified Start Speed in

order to detect Trip Start.

Ignition Off Timeout

– timeout to wait if the ignition was off, to detect Trip

stop.

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 45 / 122

Результаты поиска

Содержание DB3

Отзывы: