manualshive.com logo in svg

REWIRE SECURITY DB3, Руководство пользователя, Страница: 27 / 122

Поделиться
Скачать
REWIRE SECURITY DB3 Скачать руководство пользователя страница 27

To prevent generating false events, harsh acceleration and harsh braking 
are monitored only when following conditions are fulfilled:  

• 

Ignition (Configured to be detected by Power Voltage, Ignition or 
Accelerometer) is turned on.  

• 

Vehicle speed is equal or higher than 10km/h.  

• 

Harsh cornering is monitored only when following conditions are 
fulfilled:  

• 

Ignition (Configured to be detected by Power Voltage, Ignition or 
Accelerometer) is turned on.  

• 

Vehicle speed is equal or higher than 30km/h.   

Note

: Green Driving Scenario is a factor in various cars and various drivers 

testing phase and can be subject to changes. Rewire Security is constantly 
working on the improvement of the functionality of the devices, and 
strongly recommends using the latest version of the firmware.   

Over Speeding Scenario

 helps to prevent from exceeding fixed speed and 

inspects driver if needed. Over Speeding event is generated only when 
the vehicle speed exceeds configured “Max allowed speed “ 

Excessive Idling Detection Scenario

 informs you if your vehicle is 

stationary but the engine is on for a selected period of time to help you to 
save fuel.  

Jamming detection Scenario

 detects GSM connection jamming to inform 

you that your vehicle security could be in danger.  

Alarm Scenario

 generates an event if DB3 Plug&Play receives an alarm 

command from the remote control.  

Unplug detection Scenario

 generates an event when DB3 Plug&Play is 

plugged out of OBD socket. There are two types of detection: simple – 
used in cars, where power voltage is not dependant on ignition 
(recommended); advanced – used in cars, where power voltage is 
disconnected when the ignition is switched off. 

5.4.2

  

Trip  

 

The trip customizable feature enables user extended monitoring of performed 
trips (from engine start at present location to engine stop at arrived location), 

Содержание DB3



























































































































Отзывы:

Нет отзывов