REWIRE SECURITY DB3 Скачать руководство пользователя страница 112

Страница: 112 / 122

9.8.4 I/O#1 Low level (ID=1303)

The parameter defines the low value of triggered I/O property. This parameter
is used to set thresholds for I/O properties to generate events.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

-
2147483648

2147483647

I/O#1 property
parameter (ID=1300)

I/O#1 priority (ID=1301)

I/O#1 High level
(ID=1302)

I/O#1 logic operand
(ID=1304)

I/O#1 averaging length
(ID=1305)

S32

9.8.5 I/O#1 Logic Operand (ID=1304)

Parameter defines when event is sent: 0 – on range exit; 1 – on range entrance;
2 – both; 3 – monitoring; 4 – hysteresis.

Minimal
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

I/O#1 property
parameter

(ID=1300)

I/O#1 priority (ID=1301)

I/O#1 High level
(ID=1302)

I/O#1 Low level
(ID=1303)

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 112 / 122

Результаты поиска

Содержание DB3

Отзывы: