REWIRE SECURITY DB3 Скачать руководство пользователя страница 102

Страница: 102 / 122

9.6.13 Trip (ID=1280)

This parameter enables the ability to detect START and STOP of the trip.

Possible values are

: 0 – disabled (default), 1 – standard, 2 – private/business.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

9.6.14 Start Speed (ID=1281)

This parameter represents speed, which is detected as minimum speed to
indicate TRIP START and generate event.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

255

9.6.15 Ignition Off Timeout (ID=1282)

This parameter represents timeout to wait if the ignition is off in order to
detect TRIP STOP and generate an event.

Minimum
value

Maximum
value

Recommended

value

Goes with (depends on)
parameters

Value
type

65535

Ignition Source (ID=1003)

Mode Switch Source
(ID=1002) Trip (ID=1280)

U16

Содержание DB3



























































































































Результаты поиска

Содержание DB3

Отзывы:

REWIRE SECURITY DB3, Руководство пользователя, Страница: 102 / 122

Результаты поиска

Содержание DB3

Отзывы: