manualshive.com logo in svg

Reveal ZERO ZONE, Руководство по установке и эксплуатации, Страница: 10 / 25

Поделиться
Скачать
Reveal ZERO ZONE Скачать руководство пользователя страница 10

8  •  Installation & Operation

INSTALLATION & OPERATION

Lineup Assembly 

Zero Zone display cases have been designed for continuous display so that multiple cases may be joined together to create a lineup of any 

desired length. The cases will be ready for assembly after removing the packaging material. However, do not remove the protective coating on 

the hand rail, canopy, and honeycomb holder at this time.

A case lineup must be properly aligned, which starts with properly leveling the case (

See "Leveling" on page 6

). It is crucial to use a laser 

level to measure the high points in the floor and properly shim each base location.

Before joining cases, remove all shipping blocks inside the bases and the steel support braces under the end panels. There are bolts that go up 

through the support plates into the underside of the foamed floor.

A case must be prepared with Butyl caulk before setting the next case in the lineup. Case caulking instructions and caulk are shipped with every 

case (

See Figure 10 on page 9

).

Move the next case into position and bolt it to the first case using the 4 joining bolts that are provided. Begin tightening the bolts at the top 

rear, working down the back of the case and to the bottom front, making sure that the case seams are flush. To align cases, use a drift pin or 

screwdriver on the alignment holes in the end frames, located 7" in from the joining holes. 

Do not pull cases together using joining bolts.

The interior case seams must be sealed using silicone sealant for NSF compliance (

See Figure 11 on page 10

). Do not allow Butyl caulk 

and silicone sealant to contact one another as this may affect adhesion or color of each.

 FIGURE 9: Case Squareness

1.  Measure squareness from top right corner of the case to the bottom left 

corner of the case.

2.  Measure again from the top left corner of the case to the bottom right 

corner of the case.

3.  Measurements should be equal. Difference should be no more than 1/8".

DR-371-B

Содержание ZERO ZONE


























Отзывы:

Нет отзывов