1
2
3
Instruction Manual
TR606 Portable AM/FM Cassette Player & Recorder
PARTS INTRODUCTION
POWER SUPPLY
1. Open the battery compartment door (6), push down to
open the battery door.
2. The appliance uses 2pcs (AA/LR6) batteries, please
put the batteries into batteries compartment (6)
according to the polarity.
3. You can also pug in 4.5V DC adaptor to DC jack (7) when you use the unit.
1. Rod Antenna
2. Microphone Jack
3. Earphone Jack
4. Tuning Knob
5. Function Switch
6. Battery Door
7. DC Jack
8. Stop Button
9. Play Button
10. Fast Forward Button
11. Rewind Button
12. Record Button
13. Volume Control
14. AM/FM Dial Scale
ATTENTION
1. Do not use the new and old or different type batteries together.
2. In order to prevent the leakage of the electrolysis liquid or danger of explosion, do not
charge, heat or resolve the batteries.
3. If you do not use the appliance for a long time, please out the batteries, lest the leakage
of the battery corrodes the parts in the radio.
4. If the sound is distorted or the volume is faint, please change the batteries in time.
ANTENNA OPERATION
1. When listen to radio, please pull out the FM antenna (1) to obtain the best effect.
2. When listen to AM, it’s using the internal magnetic antenna. You can get the optimum
reception by rotating the direction of the radio.
RADIO RECEPTION
1. Set the function switch (5) to AM or FM. Select the desired radio band with the band
switch.
2. Set the tuning knob (4) to a radio station.
3. Adjust the volume control (13) to the desired level.
4. To switch off the radio, set the function switch to tape.
CASSETTE OPERATION
Open cassette door and close it after insert a tape inside.
Set function switch (5) to tape.
A. Cassette playback
1. Press play button (9) for tape playback.
2. Increase or decrease the volume
by volume control (13).
3. Press fast forward (10) or rewind
button (11) to the segment of tape
you need.
4. Press stop button (8) at any time
to stop playback, when the end of
the tape has been reached, tape
playback stops automatically.
B. Cassette recording
1. Recording from built-in microphone
Press record (12) and play button (9) together, the tape will record voice or sound by
built-in microphone.
2. Recording from external microphone plug in external
microphone to microphone jack (2), Press record (12)
and play button (9) together, the tape will record voice
or sound via external microphone.
3. Recording from radio
1) Set the function switch (5) to AM or FM and turn to your desired station by tuning knob
(4), follow the instructions in the radio reception section.
2) Press recording (12) and play button (9) together, the tape will record the sound from
radio.
Remarks:
1. Press stop button (8) to stop the recording operation.
2. The volume control (13) does not affect the recording level due to ALC circuit inside unit.
When recording from built-in or external microphone, to obtain the best result and reduce
saturation risks, speak at a distance of approximately 5 to 8cm from microphone. When
recording from AM radio, you may receive interference.
3. Protection against accidental erasure. When you record on a cassette, the previous
recording are erased automatically. To protect them against any risk of accidental erasure,
cassettes are provided with protective tabs. For this purpose, remove the protective tab
(or both) located at the top of the cassette using a knife or a screwdriver. If you subsequ-
ently need to re-record on a cassette protected in this way, you can cancel this protection
by covering the hole revealed with apiece of adhesive tape. It is not possible to press the
record button if the protective tab has been removed and has not been
replace by adhesive tape.
EARPHONE
When listen to the radio or tape, in case of
disturb other people, you can use earphone.
