manualshive.com logo in svg

Repotec GEPOESM-ESW26K Series, Руководство по установке и началу работы

Поделиться
Скачать
Repotec GEPOESM-ESW26K Series Скачать руководство пользователя страница 33

 

CABLE LABELING AND   

CONNECTION 

RECORDS 

 

When planning a network installation, it is essential to label the opposing ends of 

cables and to record where each cable is connected. This will allow user to easily 

locate inter-connected devices, isolate faults and change your topology without 

need for unnecessary time consumption. 

 

To best manage  the physical implementations of your network, follow these 

guidelines: 

 

◆

 

Clearly label the opposing ends of each cable. 

◆

 

Using your building’s floor plans, draw a map of the location of all 

network-connected equipment. For each piece of equipment, identify the 

devices to which it is connected. 

◆

 

Note the length of each cable and the maximum cable length supported by 

the switch ports. 

◆

 

For ease of understanding, use a location-based key when assigning 

prefixes to your cable labeling. 

◆

 

Use sequential numbers for cables that originate from the same equipment. 

◆

 

Differentiate between racks by naming accordingly. 

◆

 

Label each separate piece of equipment. 

◆

 

Display a copy of your equipment map, including keys to all abbreviations at 

each equipment rack. 

 

Publication date:  Oct.,  2012 

  Revision A3

 

25 

Содержание GEPOESM-ESW26K Series















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды