manualshive.com logo in svg

REPLIGEN XCell Lab XC-LAB-D, Руководство пользователя

Поделиться
Скачать
REPLIGEN XCell Lab XC-LAB-D Скачать руководство пользователя страница 29

 

  

 

XCell™ Lab Controller 

User Guide 

 

 

29          repligen.com           XC-LAB-UG-V4 

Table 10. Pump status messages examples 

Image 

Messages displayed  Explanation 

 

Priming 

The first series of cycles performed to prime the ATF 

pump and remove most or all of the air in the XCell 

ATF® Device and tubing. 

 

Zeroing FT 

The controller stops the ATF pump and waits until there 

is no flow in the A2B line and then zeros the flow 

sensor. 

N/A 

Waiting 

Shown rarely in dual mode during the initialization 

stage, for example, if the system is waiting for liquid 

flow to stop in the second ATF before zeroing the 

sensors. 

 

Detecting MinPress 

The controller runs an automated algorithm to 

determine the minimum driving pressure required to 

move the diaphragm. 

 

Stopped 

A Stop button has been pressed on the HMI. 

 

Paused 

A blue Pause button has been pressed, either on the 

HMI or on the side of the controller. 

 

Pressurizing 

The controller is performing the P-stroke, i.e. 

pressurizing the diaphragm and moving it up displacing 

liquid into the vessel. 

 

Exhausting 

The controller is performing the E-stroke, i.e. 

exhausting the diaphragm and moving it down 

displacing liquid into the ATF pump. 

 

7.8.4

 

Dual mode 

XCell ATF® 

D

 and 

D-P

 controller models can run two  XCell ATF® Devices at the same time.  If the 

devices are  same size and connected to a single bioreactor, they may be run in one of three 

synchonized modes (

Table 11

).  To  switch from the single to dual mode, open the settings > ATF 

configuration sub-menu (

Figure 23

) and select an XCell ATF® Device for the B channel then 

bioreactor configuration and select a configuration (

Figure 24

) the ATF Flow Pop-Up and select the 

desired mode. 

(Figure 17

) 

 

Note:

 Modes can be switched even while the devices are running; it takes one to two full cycles 

before the new mode goes into full effect. 

Содержание XCell Lab XC-LAB-D






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды