REPLIGEN XCell Lab XC-LAB-D Скачать руководство пользователя страница 28

Страница: 28 / 69

XCell™ Lab Controller

User Guide

28 repligen.com XC-LAB-UG-V4

7.8.1

Changing ATF Flow set points

ATF Flow Set Points (SP) can be changed at any time, including while the XCell ATF® Device is

running. Pressing the white box of the ATF Flow Rate SP (

Figure 17

) opens a dialog box, prompting

for the new set point. If the entered value lies within the allowable range, the new value is

immediately implemented. The theoretical Shear Rate SP is also calculated and displayed below the

ATF Flow Rate SP.

If you are unsure of what Set Point is right for your process, contact a local FAS to discuss the impact

of changing the ATF Flow rate for your process.

7.8.2

Starting, pausing and stopping an XCell ATF® Device

Table 9. Starting, pausing and stopping an XCell ATF® Device instructions

Actions

Steps and explanations

Start an

XCell ATF® Device

Press the corresponding

ATF Flow

Box which opens the

ATF-A (or -B) Flow pop-

window, and then press

Start

Pause an

XCell ATF® Device

Press

Pause

on the

ATF Flow pop-up OR

Press corresponding

All Pause

button on ATF Main screen. Each

All Pause

button pauses one ATF in independent mode, and both ATFs in dual mode.

Press the appropriate Device PAUSE button on the controller. The buttons on

the hardware match the functionality of those on the software.

Pause

is typically used mid-run, for instance to change out an XCell ATF®

Device, or to adjust something momentarily before continuing as before. If you

plan to stop then restart the XCell ATF® Device within the same process, the

Pause

button should be used instead of

STOP

. Upon pressing

Start

again, the

controller will resume using the settings and valve positions at the time the

process was paused.

Once device is paused,

All Pause

button becomes colorless and cannot be

pressed. Upon re-start, the controller starts without utilizing previous settings.

Stop an

XCell ATF® Device

Press

Stop

on the

ATF Flow pop-up.

Stop

is recommended to be used only at the end of a run.

Figure 18. XCell ATF® Device status - running, paused or stopped

7.8.3

Pump status box

An animated graphic in the

Pump Status

box shows real-time diaphragm movement. The message

displayed describes the action performed by the controller on the diaphragm. Pump status messages

include:

Running Paused Stopped

Содержание XCell Lab XC-LAB-D






































































Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды

REPLIGEN XCell Lab XC-LAB-D, Руководство пользователя

Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды