15
14
7
8
9
13
12
10
11
18
25
26
23
22
21
24
16
20
17
6
1
2
3
4
5
19
300-23025
1
27
Jaw housing lock screw
Jaw housing
Rotary shaft assy
Jaw clamping knob assy
Lube o-ring
Rotary head
300-23019
300-23011
12
13
Jaw
120-01055
300-23023
300-23006
130-03016
290-40290
9
10
11
7
8
4
5
6
3
2
1
1
120-01141
25
1
1
1
1
1
290-40262
250-40007
252-40163
252-40156
22
23
24
21
290-40253
290-40500
120-01147
17
18
16
Mounting screw
1
Cradle arm lock screw
Cradle support
Cradle support tens. screw
Pedestal base stem
Std. stem support assy
Pedestal base assy
Cradle support collar assy
1
1
1
1
1
1
1
Description
Part No.
Item
Qty.
Part No.
Item
Description
Qty.
290-40286
290-40281
14
15
Rotary tension screw
Material clip assy
1
1
19
130-03052
1
26
290-40858
Stem Lock Knob assy
1
O-ring for end cap screw
Hex key set (not shown)
Lubricate all threads and moving parts as needed.
120-01510
290-40806
290-40277
120-01038
290-40282
290-40279
Delrin washer
Actuator support assy
Support lock screw
Rotary actuator assy
End cap
End cap screw
1
1
1
1
1
1
Center line
Cradle arm lock screw
Stem lock knob
Hole (for torque)
Cradle support
collar
Cradle support
tension screw
Rotary tension screw
Rotary shaft
Cradle arm
Cradle
Cradle Adjustments:
Detail 1
Vise Head Assembly:
04/14 P3004
Cradle support
2,037,995
2,535,148
R
Note:
We urge you to take time to familiarize yourself with the mechanics of
your presentation vise. Rotary tying can be easier and more productive
see tips (opposite page). Please return your warranty card to validate
your warranty.
Your vise has been assembled and lubricated at the factory. All you have to do
is attach it to your existing c-clamp or pedestal base as shown below. The jaws
on your vise have been hardened and treated with a mil-spec corrosion resistant
coating. After use they should be coated with oil or a rust inhibitor like WD-40
to prevent rust or oxidation caused by acidity in your fingers.
Please note, our warranty does not cover rust damage.
1. Loosen stem lock knob enough to prevent interference with stem. Slide stem into the hole
of pedestal base and secure the stem by tightening the stem lock screw.
2. Slide cradle support collar onto pedestal stem as shown below. (flat side up)
3. Place cradle support on stem as shown.
4. Spin vise head onto threaded end of stem and tighten. Use a hex key or a nail in the hole of
the stem for torque if necessary. Be careful not to cross the threads when attaching.
5. Slide cradle arm into the hole in the cradle support and secure.
6. Slide cradle support and cradle support collar up or down on stem so that the cradle is
on the center line of the rotary shaft as shown below.
7. Loosen the stem lock screw to turn the vise to the desired position.
Slide the cradle arm into the hole in the cradle support. Always adjust the cradle arm
1.
so that the cradle is close to the eye of the hook. This prevents having to wind up alot
of thread after rotary tying.
2. Use the cradle support tension screw to add a little drag to the cradle support
so that the cradle still swings relatively easy.
3. If the cradle is in an awkward position for you it can be rotated as shown in detail 1.
The cradle is fairly snug on the arm so be sure to firmly hold the wire to prevent bending it.
Rotate
Renzetti Presentation 3000 Series
True Rotary
Model # P3004 Pedestal Base Vise
For the complete line of Renzetti products and accessories. Please visit our website:
www.renzetti.com or truerotary.com
Covered under U S Patent & Registration No.:
2,51441; 2,077,565; 2,060,740; 2,567,674
2,535,148; 6,564,494B2; 2,037,995
Made in the USA 04/14
1
Cradle assy
290-40264
20
1
