Renesas SDI Emulator System M32100T-EZ-E Скачать руководство пользователя страница 7

Страница: 7 / 44

( 5 / 42 )

Chapter 1. Precautions for Safety

This chapter describes precautions for using this product safely and properly. For precautions of the emulator and emulator
debugger, refer to each user's manual.

1.1 Safety Symbols and Meanings ..................................................................................................... 6

Warnings for AC Power Supply .................................................................................. 7

Warnings to Be Taken for This Product ...................................................................... 7

Warning for Installation ............................................................................................... 7

Warning for Use Environment ..................................................................................... 7

Cautions for Power Supply .......................................................................................... 8

Cautions for Powering Up Sequence ........................................................................... 8

Caution for Installation ................................................................................................ 8

Cautions to Be Taken for Handling This Product ........................................................ 8

Caution for Abnormal Operation ................................................................................. 8

Notes on Product Information ...................................................................................... 9

Notes on Downloading Firmware ................................................................................ 9

Notes on USB Interface ............................................................................................... 9

Note on Dependencies on the MCU Model ................................................................. 9

Note on Stack Capacity and Stack Pointer .................................................................. 9

Notes on Target Program Execution in Real-time ..................................................... 10

Note on Specifying Breakpoints ................................................................................ 10

Notes on Reset Control Switch .................................................................................. 10

Note on Using Reset Mask ........................................................................................ 10

Note on LED Display................................................................................................. 10

Note on Access Prohibited Areas .............................................................................. 10

Notes on Target System ............................................................................................. 11

CAUTION

WARNING

IMPORTANT

Содержание SDI Emulator System M32100T-EZ-E












































Результаты поиска

Содержание SDI Emulator System M32100T-EZ-E

Отзывы:

Похожие инструкции для SDI Emulator System M32100T-EZ-E

Бренды по названию

Популярные бренды

Renesas SDI Emulator System M32100T-EZ-E, Руководство пользователя

Результаты поиска

Содержание SDI Emulator System M32100T-EZ-E

Отзывы:

Похожие инструкции для SDI Emulator System M32100T-EZ-E

Бренды по названию

Популярные бренды