manualshive.com logo in svg

Renesas RX100 Series, Руководство пользователя

RX100-серия от Renesas - это высокопроизводительные микроконтроллеры с передовыми возможностями для различных применений. User Manual с подробной информацией доступен для бесплатного скачивания на manualshive.com. Познакомьтесь с функционалом и возможностями продукта прямо сейчас!

Поделиться
Скачать
background image

R01UH0822EJ0100 Rev.1.00

Page 103 of 1041

Jul 31, 2019

RX13T Group

6. Resets

Figure 6.2

Operation Examples During Voltage Monitoring 1 Reset and Voltage Monitoring 2 Reset

6.3.4

Independent Watchdog Timer Reset

Independent watchdog timer reset is an internal reset generated by the independent watchdog timer.
Output of the independent watchdog timer reset from the independent watchdog timer can be selected by setting the 
IWDT reset control register (IWDTRCR) and option function select register 0 (OFS0).
When output of the independent watchdog timer reset is selected, an independent watchdog timer reset is generated if the 
independent watchdog timer underflows, or if data is written outside the refresh-permitted period. When the internal 
reset time (tRESW2) has elapsed after the independent watchdog timer reset has been generated, the internal reset is 
canceled and the CPU starts the reset exception handling.
For details on the independent watchdog timer reset, see 

section 22, Independent Watchdog Timer (IWDTa)

.

6.3.5

Software Reset

The software reset is an internal reset generated by the software reset circuit.
When A501h is written to SWRR, a software reset is generated. When the internal reset time (tRESW2) has elapsed after 
the software reset is generated, the internal reset is canceled and the CPU starts the reset exception handling.

External voltage 

VCC

Vdeti*

1

RES# pin

Voltage detection i 

signal (Low is valid)

tLVDi*

2

RES# pin reset

RSTSR0.LVDiRF

tLVDi*

2

RES# pin reset

RSTSR0.LVDiRF

LVCMPCR.LVDiE

LVDi valid setting

LVDiCR0.LVDiRN = 0

LVDiCR0.LVDiRN = 1

Voltage detection i 

signal (Low is valid)

Internal reset signal

Internal reset signal

Note:

For details on the electrical characteristics, see the Electrical Characteristics section.

Note 1. Vdeti shows a detection level of voltage monitoring 1 reset and voltage monitoring 2 reset. (i = 1, 2)
Note 2. tLVDi shows a time for voltage monitoring 1 reset and voltage monitoring 2 reset. (i = 1, 2)

Содержание RX100 Series


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RX100 Series

e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Бренд: e-Line Technology Страницы: 34
Yamaha EMP100 Supplementary Manual preview
EMP100
Бренд: Yamaha Страницы: 4
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Бренд: ESD Страницы: 28
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Бренд: janitza Страницы: 28
Analog Devices EZ-Extender Analog 120-Pin Probing Board Manual preview
EZ-Extender Analog 120-Pin Probing Board
Бренд: Analog Devices Страницы: 29
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Бренд: Orolia Страницы: 167
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Caen A 1735 Technical Information Manual preview
A 1735
Бренд: Caen Страницы: 14
VCS VIP 1000 User Manual preview
VIP 1000
Бренд: VCS Страницы: 118
Observint NVR16 Firmware User Manual preview
NVR16
Бренд: Observint Страницы: 117
Intel 500 - DATASHEET REV 003 Datasheet preview
500 - DATASHEET REV 003
Бренд: Intel Страницы: 67
UNICORECOMM UM620N User Manual preview
UM620N
Бренд: UNICORECOMM Страницы: 19
LUX LUMEN 10230 Manual preview
10230
Бренд: LUX LUMEN Страницы: 41
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Бренд: Vivint Страницы: 2
Zonet ZEN3320E Quick Installation Manual preview
ZEN3320E
Бренд: Zonet Страницы: 1
Sony Ericsson GC86 Quick Start Manual preview
GC86
Бренд: Sony Ericsson Страницы: 2
Intel SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz Specification preview
SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz
Бренд: Intel Страницы: 56
Spectrum Digital XDS510USB Installation Manual preview
XDS510USB
Бренд: Spectrum Digital Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды