Rendamax E8.1121 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 44

Rendamax E8.1121 Скачать руководство пользователя страница 24

Operation

Overview of display values and settings

INSTALLATION

Designation

Value range

Default

IV

CODE-NO

0000 - 9999

Entry

CODE-NO
(Adjustment)

0000 - 9999

0000

BUS ID HS1

00 - 08

00

BUS ID 1

(- - - - ,00), 01-15

01

BUS ID 2

(- - - -), 02-15

02

BUS TERMINATI-
ON

00, 01 (OFF/ON)

01 (0631)
00 (1121)

AF SUPPLY

00,01

01 = ON

TIME MASTER

00, 01

00 = OFF

Expert area

Hinged cover OPEN

Î

search for

level on right with

Ç

, open with

Ä

These settings can only be changed if
the code no. is entered (see page 6).

E

If these values are set incorrectly,

they may cause malfunctions or

damage to the system.

CODE-NO

Entering the code number (see page 6)
allows all of the expert settings to be
modified => including the code number
itself (first parameter)
(

Ç

on right => CODE-NO 0000

Ä

=>

Ç

1st digit

Ä

=>

Ç

2nd digit

Ä

=>

Ç

3rd digit

Ä

=>

Ç

4th digit

Ä

=>

Ç

)

BUS ID HS1

For cascades, the HS are numbered
beginning with "01“. ("00“ = Single
boiler)

BUS ID1 / 2

(heating circuit number)

The heating circuits are sequentially
numbered starting with "01". heating
circuit numbers must not be assigned
twice. For replacement controllers,
please enter exactly the same heating
circuit numbers as the replaced
controller.

BUS TERMINATION

This parameter is used to switch the
terminal resistance for Can communi-
cation. The entire system may contain
exactly

one

terminating resistor.

Delivery state:
-

Mixer controller (1121) => „0“

(Parameter BUS ID HS1 > 00 =>
Bus terminator = 00)

E

When loading the factory settings,

the terminal resistance is newly set

(according to boiler sensor).

AF SUPPLY

(Outdoor sensor power

supply)
Switching off the power supply to the
outdoor sensor. Switching off allows up
to 5 controllers to be operated with a
single outdoor sensor. The power
supply must only be switched on if
there is one controller per sensor = "01".

TIME MASTER

(Only without or TIME

MASTER in system)
00 no time master => each heating
circuit has its own time
01 controller is time master => all
controllers and remote controls take
over the time settings of this controller.

!

No more than 1 TIME MASTER is

permitted in the system!

24

«
...
22
23
24
25
26
...
»

Содержание E8.1121













































Отзывы:

Нет отзывов