REMKO CMF 120 Скачать руководство пользователя страница 75

Страница: 75 / 88

Spare parts list outdoor module CMF/CMT 120

Nr.

Designation

CMF 120

CMT 120

EDP-Number

Compressor

1120070

Laminated heat-exchanger

1120071

Four-way switching valve

1120072

Shut-off valves

1120073

Fan blade

1120074

Cover panel

1120075

Side panel, left

1120076

Front panel

1120077

Fan protection guard

1120078

Side panel, right rear

1120079

Side panel, right front

1120195

Cover, rear

1120196

Cover, front

1120197

Recessed grip

1120198

Grille, rear

1120199

Spare parts (not illustrated)

Fan motor

1120206

Sensor

Available only by request with the device no.

Control board

Available only by request with the device no.

Mains filter board

Available only by request with the device no.

Power electronics

Available only by request with the device no.

When ordering spare parts, please state the computerised part no., device number and device type (see

type plate)!

Содержание CMF 120

























































































Результаты поиска

Содержание CMF 120

Отзывы:

REMKO CMF 120, Руководство по сборке и эксплуатации, Страница: 75 / 88

Результаты поиска

Содержание CMF 120

Отзывы: