background image

Data specific to indoor unit

BL 263 DC IT

BL 353 DC IT

Application area (room volume), approx.

m

3

80

110

Adjustment range, room temperature

°C

+17 to +30, +8 with "FP" function

Air flow volume per level

m³/h

270/320/420

370/470/570

Sound pressure level per speed setting 

5)

dB (A)

30/36/41

28/35/42

Sound pressure level, Silent/Turbo mode 

5)

dB (A)

24/42

23/43

Sound power level max. 

5)

dB(A)

54

Enclosure class

IP

X 0

Condensate drainage connection

mm

18

Dimensions: H/W/D

mm

285/715/194

285/805/194

Weight

kg

6.7

7.1

EDP no.

 

1629267

1629357

5)

 At distance of 1m in the open air; specified values are maximum values

Data specific to outdoor unit

BL 263 DC AT

BL 353 DC AT

Power supply

V/Ph/

Hz

230/1~/50

Operating range, cooling

°C

+5 to +50

Operating range, heating 

7)

°C

+5 to +30

Air flow rate, max.

m³/h

1800

Enclosure class

IP

24

Sound power level max. 

5)

dB (A)

58

60

Sound pressure level 

5)

dB (A)

56

Refrigerant 

6)

 

R 410A

Refrigerant, basic capacity

kg

0.74

CO

2

 equivalent

t

1.54

Max. operating pressure

kPa

4200 / 1500

Refrigerant piping, max. length

m

3, 5, 8

3, 5, 8

Refrigerant piping, max. height

m

5

5

Dimensions: H/W/D

mm

555/770/300

Weight

kg

26.3

25.7

EDP no.

 

1629266

1629356

5)

 At distance of 1m in the open air; specified values are maximum values

6)

 Contains greenhouse gas according to Kyoto protocol, GWP 2088

7)

 This can be extended to -20 °C with the appropriate accessory kit

 

 

 

 

 

9

Содержание BL 263 DC

































































Отзывы: