REMEHA Gas 120 ACE - 115 Скачать руководство пользователя страница 12

Страница: 12 / 96

3 Technical specifications

3.1

Homologations

3.1.1

Standards & Directives

This product complies with the requirements of the following European

directives and standards:

Standards: EN15502
Efficiency Directive 92/42/EC
Low Voltage Directive 2014/35/EU

Generic standard: EN 60335-1

Relevant standard: EN 60335-2-102
Electromagnetic Compatibility Directive 2014/30/EU

Generic standards: EN 61000-6-3, EN 61000-6-1

Relevant Standard: EN 55014
Ecodesign Directive

This product conforms to the requirements of European Directive

2009/125/EC on the ecodesign of energy-related products.

In addition to the legal requirements and guidelines, the supplementary

guidelines in this manual must also be followed.
Supplements or subsequent regulations and guidelines that are valid at

the time of installation shall apply to all regulations and guidelines

specified in this manual.

Warning

The appliance must be installed by a qualified professional in

accordance with applicable local and national regulations.

3.1.2

Factory test

Before leaving the factory, each appliance is tested for the following:

Electrical tests (components, safety).

3 Technical specifications

MID _HMI T-control - Gas 120 ACE

7717201 - v03 - 25062019

Содержание Gas 120 ACE - 115

































































































Результаты поиска

Содержание Gas 120 ACE - 115

Отзывы:

REMEHA Gas 120 ACE - 115, Руководство пользователя, Страница: 12 / 96

Результаты поиска

Содержание Gas 120 ACE - 115

Отзывы: