Reiner jetStamp graphic 970 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 94

Reiner jetStamp graphic 970 Скачать руководство пользователя страница 84

PCset graphic Help 970

84

ERNST REINER GmbH & Co. KG

7.2

Reasons for rechargeable batteries not being charged

- No rechargeable batteries inserted or rechargeable batteries inserted incorrectly
- Contacts in the battery compartment defective
- Temperature of rechargeable batteries above 40 degrees Celsius
- Rechargeable batteries too old
- Rechargeable batteries defective
- Rechargeable batteries completely discharged (deep discharge)

Capacity and service life

The rechargeable batteries reach their full capacity after several charge/discharge cycles.
With increasing age, the rechargeable batteries' operating time reduces.
Batteries are subject to wear. A longer service life than six months cannot be warranted.

7.3

Visual Signals (LED)

When the indicator flashes orange (warning), the status display

of the PCset graphic

software shows a detailed device message

(see "Operating Interface").

LED
indicator

Condition

Cause

Removal

Notes

Green

Ready

Green

Flashing

Device is in standby
mode

Switch off and on

again or push trigger
button

The power saving
mode is activated
automatically after
10 minutes when the
device is not in use.

Orange

(warning)

Flashing,

interval of 1

- No or defective

print cartridge

- Wrong print

cartridge

- Ink level writing

error

- Print cartridge not

inserted

- Rechargeable

battery empty

- No rechargeable

battery/defective
rechargeable
battery

- Print carriage

movement
blocked

- Print images have

been deleted

Insert print

cartridge

Insert print

cartridge correctly

Charge recharge-

able battery

Insert/replace

rechargeable battery

Transfer new print

images

The detailed cause
and removal can be
determined in the

of

the PCSet graphic
software

«
...
82
83
84
85
86
...
»

Содержание jetStamp graphic 970































































































Отзывы:

Нет отзывов