manualshive.com logo in svg

Regin RDAS-24C Series, Руководство пользователя, Страница: 15 / 18

Поделиться
Скачать
Regin RDAS-24C Series Скачать руководство пользователя страница 15

Variable list

1409

ASN [Char_16…15]

R

Each register: Two
bytes, each coding
an ASCII char.
ASN is coded
beginning with reg.
1409

Example:
0x47 44 = GD
0x42 31 = B1
0x38 31 = 81
0x2E 31 = .1
0x45 2F = E/
0x4D 4F = MO
-> ASN is GDB181.1E/MO

1410

ASN [Char_14…13]

R

1411

ASN [Char_12…11]

R

1412

ASN [Char_10…9]

R

1413

ASN [Char_8…7]

R

1414

ASN [Char_6…5]

R

1415

ASN [Char_4…3]

R

1416

ASN [Char_2…1]

R

Reserve

4.1.1

Register 769 "Status"

Status

Bit 00

1 = reserved

Bit 06

1 = Adaption done

Bit 01

1 = Backup mode active

Bit 07

1 = Adaption in progress

Bit 02

1 = reserved

Bit 08

1 = Adaption error

Bit 03

1 = reserved

Bit 09

1 = Selftest failed

Bit 04

1 = Mechanical fault, device jammed or
manual override

Bit 10

1 = Selftest passed

Bit 05

1 = Nom. lifetime exceeded

Bit 11

1 = Invalid configuration

4.1.2

Supported function codes

Function codes

03 (0x03)

Read Holding Registers

04 (0x04)

Read Input Register

06 (0x06)

Write Single Register

16 (0x16)

Write Multiple Registers (Limitation: Max. 120 registers within one message

4.2 Parameter and function description

Function

Reg.

Description

Override
control

2

The actuator can be operated in override control for commissioning / maintenance purposes or system-wide
functions (e.g. night-cooling).

✓

Manual override: When the gear disengagement is used to freely adjust the damper position, a mechan-
ical jam will be detected if a mismatch between setpoint and actual position persists for more than 10
seconds.

✓

Remote override: The actuator enters this state when an override command is sent over the bus

✓

Available commands:
- Open /Close (depends on opening direction)
- Min / Max (depends on Min/Max settings)
- Stop

Adaptive
positioning

258

✓

For air dampers where the opening range is smaller than the nominal opening range 0…90°, the feedback
signal can be adapted to have the actual opening range represented as 0…100%.

✓

Using adaptive positioning makes the actuator driving to its end positions at the first startup after acti-
vating the adaptive positioning.

✓

To trigger the adaptation again after the first startup, either the command "CalibrateAdaption" (Write "1"
into register no. 256), or the adaptive positioning can be turned off and on again.

RDAS…-24C variable list, Rev. A

15

Содержание RDAS-24C Series



















Отзывы:

Нет отзывов