background image

8

 | 

Regency CS1200  Freestanding Wood Stove

 | 

8

installation

Z

6"

6"

16"

Y

Y

X

X

6"

for angled

corners

6"

16"

6"

6"

Z

The Regency Freestanding models have been alcove approved and must be installed 

with a listed double wall connector to the ceiling level. 

Note:  Minimum alcove ceiling height - 84"

 

  Maximum depth of alcove - 36"

    Minimum Overall Width (X) of Floor 

       Protector

 

for all installations: 

 US 

38-3/4"

 

 Canada 

42-3/4"

 

Floor Protection

A combustible floor must be protected by a non-combustible material (like tile, 

concrete board, or certified to UL-1618 or as defined by local codes) extending 

beneath the heater and a minimum of 6" from each side and minimum 16" from 

the fuel door opening of the stove and minimum 6" (or the rear clearance to 

combustibles whichever is smaller) from the rear of the stove. 

NOTE: In Canada, floor protection must extend 18" to the front and 8" to each side of the stove.

Minimum Alcove Clearance to Combustible Materials

Unit

From Back Shield

+ Side Shields.

From Flue

Center-Line

Min.

Width

Min. Hearth
to Rear Wall

CS1200

G

H

I

J

K

L

11"

7"

24-1/2"

14-1/2"

49-1/8"

39-1/4"

Minimum Overall Depth (Y) of Floor Protector

Unit

Residential

"C" Vent

Residential

Close Clearance

Mobile Home

Close Clearance

Alcove

CS1200

Y

Z

Y

Z

Y

Z

Y

Z

USA

39"

6"

39

6"

39"

6"

39"

6"

Canada

43"

8"

43"

8"

43"

8"

43"

8"

MINIMUM ALCOVE CLEARANCE AND CLEARANCE TO COMBUSTIBLE MATERIALS

MEASUREMENTS "FROM UNIT" ARE FROM THE SIDE SHIELDS OF THE STOVE TO A SIDE WALL OR TO A CORNER, AND 

FROM THE REAR HEAT SHIELD TO A BACK WALL

Содержание CS1200 Alterra





































Отзывы: