Regal 32 EXPRESS Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 364

background image

9

Auxiliary Equipment Operation

To read either the fresh water or waste water monitor panel the
breaker on the main DC panel must be activated.

The monitor is normally located inside the ship’s AC/DC
cabinet or may be located behind the starboard picture
window on a trim panel.
The fresh water monitor displays the amount of  potable
water in the system. There are sensors located in the water
tank that send a signal to the display panel when activated.
Press the top portion of  the toggle switch and read the
gauge display.
The waste portion of  the display shows the amount of
waste water in the holding tank.  There are sensors located
in the waste tank that send a signal to the display panel
when activated. Press the bottom portion of  the toggle
switch and read the gauge display.
This portion of  the system needs to be monitored peri-
odically to prevent the system from being over full which
could cause equipment damage and/or a possible leak in
the vessel.
If   the  waste  system  is  determined  to  be  full  it  can  be
emptied by connecting a marina pump-out hose to the
waste fi tting located on the deck. The pump out device
will actually remove the waste much like a vacuum cleaner.
This is the easiest way to eliminate the vessel’s waste and
be environmentally friendly while performing the task.
An alternative method

which can be used in International wa-

ters only

is to pump the waste overboard using the waste

seacock.

MONITOR-WATER/WASTE

Notice the key switch portion of the monitor. The key
switch controls an overboard discharge pump (macerator)
which grinds up the waste and sends it through the hull
bottom. Make sure the waste seacock is open and you are
legal to pump overboard. Turn the macerator breaker on
and then energize the monitor panel key switch by turning
it to the “on” position and holding it while you press the
red button to activate the pump.

Be sure to turn the seacock off and secure it with a tie wrap after the
pump-out cycle is completed as you can be fi ned if authorities fi nd
the seacock in an unlocked position.

Macerator
Key Switch

FRESH WATER & WASTE MONITOR

«
...
202
203
204
205
206
...
»

Содержание 32 EXPRESS













































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 32 EXPRESS

Бренд: LaserPerformance Страницы: 11

Бренд: LaserPerformance Страницы: 16

Бренд: Quantum Sails Страницы: 11

Бренд: Ranger boats Страницы: 80

Бренд: GALA Страницы: 10

2001 37-foot Pacific Trawler

Бренд: Pacific Trawler Страницы: 33

Бренд: ABSTRACT Страницы: 10

Бренд: Hunter Страницы: 157

Бренд: 3D Tender Страницы: 23

Бренд: Ockelbo Страницы: 70

Бренд: Navigator Страницы: 26

Бренд: Quicksilver Страницы: 55

RESPONSE TXi 2021

Бренд: Malibu Boats Страницы: 202

WaveRunner SuperJet 700 2001

Бренд: Yamaha Страницы: 107

GP800R WaveRunner 2004

Бренд: Yamaha Страницы: 124

Бренд: TALAMEX Страницы: 51

Бренд: Carp Madness Страницы: 23

Бренд: WAYFARER Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды