REFU REFUsol 48K-UL Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 72

REFU REFUsol 48K-UL Скачать руководство пользователя страница 8

8

REFUsol 48K-UL

REFU Elektronik GmbH

2

Safety Information

Pos : 9 / Invert er Manuals /Sic her heits hinweise/Besti mmungsgemäß e Ver wendung/ 866/ 867 @ 1\ mod_1404740847808_641. doc x @ 6749 @ 2 @ 1

2.1

Intended Use

The REFUsol 48K-UL inverter, also referred to in these operating instructions as the inverter, is a solar
inverter, which transforms the direct current generated by the PV generator (photovoltaic modules) into
alternating current and feeds this to the public power supply network.

The inverter is manufactured according to the rules and current state of technology and takes into account
the valid EU, IEC and UL guidelines respectively.

The inverter fulfils the requirements according to protection class IP 65 / NEMA 4 and can be used indoors
and outdoors.

Any other use is not considered to be a designated use. The manufacturer accepts no liability for damages
resulting from this.

Pos : 10 /I nverter M anuals/ Sicher heit shi nweis e/ Einl eit ung/U L s pecific s af et y gui deli nes / WR UL @ 2 \mod_1469784257470_641. doc x @ 23466 @ 2 @ 1

2.2

Safety Guidelines

Commissioning and operation of this unit must be carried out by qualified personnel. Qualified personnel
includes licensed electricians, service personnel, and authorized operators who have read and fully
understood all of the technical information and the safety instructions contained in this manual.

Review the following information before attempting to install and operate the product.

2.2.1

Rules for Safe Installation and Operation

Please note the following rules:



Do not attempt to install or operate this equipment without proper training.



Ensure that this unit is properly grounded.



Ensure that all cables are properly connected.



Verify that input line voltage and current capacity are within specifications before turning on the
power supplies.



Use proper electrostatic discharge (ESD) precautions.



Always be careful around this equipment.



Never remove the upper inverter lid.



Safe operation requires correct transport, storage, assembly, installation, and operation.

Pos : 11 /I nverter M anuals/ Sicher heit shi nweis e/ Qualifi kation des Pers onals /WR UL @ 2\ mod_1469784561182_641. doc x @ 23494 @ 2 @ 1

2.3

Personal Safety

2.3.1

Suitable Personal Protective Equipment

Whenever possible, interaction with this unit should be performed under de-energized conditions.

If interaction with this unit is necessary while it is energized, always ensure that any personnel entering a
safety zone wear appropriate Personal Protective Equipment (PPE) for the specific job to be performed.
Identification of appropriate PPE is the responsibility of the PV system operator and shall be determined in
accordance with NFPA 70E and/or local jurisdictional requirements.

«
...
6
7
8
9
10
...
»

Содержание REFUsol 48K-UL









































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды