background image

reechcraft.com/powerlift   888-600-6160

59

WARRANTY

SECTION 

8

IN NO EVENT SHALL REECHCRAFT, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR 
AGENTS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, 
OR EXEMPLARY DAMAGES, INCLUDING BUT NOT LIMITED TO LOST PROFITS OR 
REVENUE, THE COST OF RENTAL OR REPLACEMENT EQUIPMENT, DOWNTIME, 
DAMAGE TO PROPERTY AND THIRD-PARTY CLAIMS, OR ANY OTHER COMMERCIAL OR 
ECONOMIC LOSSES OF ANY KIND, WHETHER BASED ON CONTRACT, TORT (INCLUDING 
THEORIES OF NEGLIGENCE, RECKLESSNESS, STRICT LIABILITY, OR DEFECTIVE 
PRODUCT LIABILITY), OR ANY LEGAL THEORY, EVEN IF ADVISED OF THE POSSIBILITY 
OF SUCH DAMAGES OR THEY ARE FORESEEABLE, ARISING OUT OF THE  
END USER’S USE OR INABILITY TO USE THE PRODUCT.  

ANY REPAIR OF THE PRODUCT UNDERTAKEN WITHOUT PRIOR WRITTEN 
AUTHORIZATION FROM REECHCRAFT WILL VOID THIS WARRANTY.

These warranties give the end user specific legal rights. As the end user, you may also 
have other rights which may vary from state to state. Some states do not allow the 
exclusion or limitation of incidental or consequential damages, so the above limitations or 
exclusions may not apply to every end user.

All claims or disputes arising under or in connection with this end-user warranty shall be 
governed under the laws of the State of North Dakota and the laws of the United States 
(without giving effect to principles of conflicts of laws). The location of any dispute shall 
be Fargo, North Dakota. Any provision of this end-user warranty which is, or is deemed 
to be, unenforceable in any jurisdiction shall be severable from this end-user warranty in 
that jurisdiction, without in any way invalidating the remaining provisions of this end-user 
warranty, and any such unenforceability in that jurisdiction shall not make that provision 
unenforceable in any other jurisdiction. 

Содержание PowerLift PL65





























































Отзывы: