RedPlate Black-n-Blues Скачать руководство пользователя | Manualshive

Страница: 1 / 11

background image

RedPlate Black-n-Blues Operations Guide

1

Black-n-Blues

Operations Manual

Welcome to the RedPlate Family, thank you for your purchase of a RedPlate Black-n-Blues
amplifier. Please take a moment and review this manual for an understanding of all the
available features (or just put all the knobs at noon and play).
This Manual applies to Black-n-Blues models produced after 03/01/2011.

Signal Path Block Diagram:

FRONT PANEL:

Input Jack

– Typical High impedance input to the amplifier. Designed to be “Pedal Friendly” in

the unlikely event you will ever use a pedal in front of the Black-n-Blues.

CLEAN PREAMP SECTION

1
2
3
...
»

Содержание Black-n-Blues












Отзывы:

Нет отзывов

Похожие инструкции для Black-n-Blues

Бренд: M-Audio Страницы: 8

Бренд: NAD Страницы: 26

Бренд: Falco Systems Страницы: 8

trans-nova P4000

Бренд: Hafler Страницы: 2

Бренд: Crunch Страницы: 2

MOON Evolution MC-8

Бренд: Simaudio Страницы: 11

Бренд: QUAD Страницы: 16

Бренд: ATI Audio Страницы: 7

Бренд: HAMTRONICS Страницы: 6

Бренд: Anthem Страницы: 7

Pro-Ject Head Box DS

Бренд: Box-Design Страницы: 4

Бренд: Hamilton/Buhl Страницы: 14

Бренд: DB Drive Страницы: 6

Бренд: Innersound Страницы: 11

Бренд: Wilson Electronics Страницы: 8

Бренд: Taiden Страницы: 99

Бренд: STUDIO PROJECTS Страницы: 3

Бренд: Onkyo Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды