background image

8

b. At night, at times of heavy fog, or at any other

times when your field of vision might be
limited and it would be difficult to gain a clear
view of the working area. 

c. During rain storms, during lightning storms, at

times of strong or gale-force winds, or at any
other times when weather conditions might
make it unsafe to use the product.

WORKING PLAN

1. You should never use the product when under

the influence of alcohol, when suffering from
exhaustion or lack of sleep, when suffering from
drowsiness as a result of having taken cold
medicine or at any other time when a possibility
exists that your judgment might be impaired or
that you might not be able to operate the product
properly and in a safe manner.

2. When planning your work schedule, allow plenty

of time to rest. Limit the amount of time over
which the product is to be used continuously to
somewhere around 30~40 minutes per session,
and take 10~20 minutes of rest between work
sessions. Also try to keep the total amount of
work performed in a single day under 2 hours or
less.

1. If you don’t observe the working time, or

working manner (See 

USING THE

PRODUCT), Repetitive Stress Injury(RSI)
could occur.
If you feel discomfort, redness and swelling
of your fingers or any other part of your
body, see a doctor before getting worse.

2. To avoid noise complaints, in general,

operate product between 8a.m. and 5p.m. on
weekdays and 9a.m. to 5p.m. weekends. 

Check and follow the local regulations as to sound
level and hours of operations for the product. 

NOTE

WARNING

5. For safe operation

Содержание BCZ2500S











































Отзывы: