background image

 

 

 

   

            

10350 STATE HWY 30 College Station, TX 7784 (979) 776-7200 

 

 

rev. 3 

   RL-101M Installation and Operation Manual 

Re 

                                                      

 

 

 

 

 

 

 

 

 

 

                                                                                                                                                   SAFETY MESSAGE

 

 

It is important to follow all instructions in this manual.  
 

 

This device is to be installed by a trained professional 
who is familiar with Redline Safety products. 
 

 

Read and understand all instructions before installation 
or use of this equipment  

 

 

Keep cover tight when circuits are alive. 

 

 

Test Instrument regularly to ensure it is operating 
properly. After installation provide a copy of manual to 
authorized personnel 

 

 

 

       IMPORTANT SAFETY WARNING 

Failure to follow all safety and operational instructions 
may result in property damage, serious injury or death.

 

 

Power Consumption and Voltage rating 

RL101M instrument is powered by 6 AA batteries 
(9VDC) internally. 

1mA continuous consumption when the device is 
operational. 

 

                   

 Head Housing Certifications 

NORTH AMERICAN CERTIFICATIONS (standard)

 

CLASS I, DIV 1 GROUP BCD , CLASS II GROUP EFG, CLASS III 
CLASS I ZONE 1 AEx d IIC, Ex d IIC (Canada) ,NEMA TYPE 4X 

 

   

RL-SSH

 

Sensor Housing Certifications

 

                

CI, D1 BCD C1, Zn 1, IIB+H2, IIB, IIA 

 

Содержание RL-101M









Отзывы: