Redline Communications RedMAX AN100U Скачать руководство пользователя страница 166

Страница: 166 / 178

Redline Management Suite Administration and Maintenance Guide

D-2

Redline Communications Inc. Confidential and Proprietary

Table D-1

AN100U/UX Synchronization Event Log Messages

Message Reported
By

Event Log Message
(Logged starting from bottom to top)

Probable Cause

Recommended Troubleshooting

Master with GPS

Master with GPS Function Activated

GPS Synchronization Ok

Backup Master is not active.

Normal Operation

Backup Master

Synchronization with Master Ok

Master Detected

Backup Master is ready, but not active.

Normal Operation

Slave

Synchronization Ok

Master Detected

Slave synchronized to Master is active.

Normal Operation

Backup Master

Synchronization with GPS Ok

GPS Detected

Backup Function Activated

Master is not Detected

Master has become disconnected, during normal operation.

Normal Operation

Backup Master

Backup Function Activated

Synchronization with GPS Ok

GPS Detected

Backup Master is now active.

Master is Offline after reboot.

Normal Operation

Backup Master

17:33:06 GPS Synchronization Ok

17:33:02 GPS Detected

17:32:31 GPS is not Detected

17:01:33 Master with GPS Function
Activated

GPS is in holdover mode

GPS antenna may have become disconnected, during normal
operation. After 30 Minutes of satellite signal loss, the GPS halts
(squelches) its signal for 30 seconds to indicate its holdover
status to the Master with GPS sector controller.

Check the GPS connection to its
external antenna. Refer to the
RedMAX GPS Clock User Manual.

Slave

Synchronization Signal not Detected

Master and Backup Master have become disconnected, during
normal operation.

Check the Master with GPS and the
Backup Master and ensure they are
online and that the GPS is
connected to the Sync Out port.

Содержание RedMAX AN100U



















































































































































































Результаты поиска

Содержание RedMAX AN100U

Отзывы:

Похожие инструкции для RedMAX AN100U

Бренды по названию

Популярные бренды

Redline Communications RedMAX AN100U, Руководство по администрированию и обслуживанию

Результаты поиска

Содержание RedMAX AN100U

Отзывы:

Похожие инструкции для RedMAX AN100U

Бренды по названию

Популярные бренды