Redline Communications RedMAX AN100U Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 178

background image

2-4

RedMAX Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

– The manufacturer and the model number of each device;

– LAN and WAN protocols used for all types of network communication.

– Logical connections. These may be listed on a separate diagram.

– The network interface of each manageable interface.

– User data and management paths must be clearly defined with appropriate VLAN

IDs and IP subnets, if applicable.

Note

It is crucial that your RedMAX system be operating on a supported software pair.

Refer to the RedMAX AN100U/UX Base Station User Guide for list of supported software
which specifies which subscriber unit software is supported with each AN100U/UX
software version. You must ensure that you are using compatible software versions.

Monitoring Your System

The ability to access your sector controllers and actively monitor various items is
imperative in order to keep the system operational at a carrier class level.

Ideally, you can install a client VPN system on the computer that you are using to monitor
your sector controllers. This allows you to both monitor and configure your system
remotely. Once the VPN is installed, you should be able to log into any of the sector
controllers using either the CLI or the Web interface.

Connecting to the Sector Controller Web Client

The following table lists the Web browsers supported in this release. This release supports
English only.

.

You will need to connect to the web interface of the sector controller to perform most
maintenance or troubleshooting procedures. You must have connectivity from your
computer to the sector controller or be connected directly to the sector controller before
you can use this procedure.

Step 1

Open one of the supported browsers.

Step 2

Enter the following command:

http:// 192.168.101.3

Table 2-3

Supported Web Browsers

Web Browser

Supported Versions

Internet Explorer

7.x

Mozilla Firefox

2.0.0.5, 3.0.5 and above

«
...
14
15
16
17
18
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: Voxx Страницы: 7

Бренд: Panasonic Страницы: 16

Бренд: NEC Страницы: 8

Бренд: 4B Страницы: 16

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 8

Бренд: Kathrein Страницы: 52

Бренд: Magura Страницы: 2

Бренд: Zacuto Страницы: 5

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

KOOLZONE SAC-1800

Бренд: UNINEX Страницы: 5

Бренд: Öhlins Страницы: 10

Бренд: +GF+ Страницы: 36

Бренд: hepco & becker Страницы: 4

Бренд: Independence paragliding Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды