INTERCHANGEABLE OLPF SYSTEM
WARNING:
Read these instructions carefully and in their entirety before removing or installing an OLPF. Damage to
the OLPF module, camera, or sensor due to improper handling or use is not covered under warranty.
WARNING:
Once an interchangeable OLPF is removed from the camera, the sensor is exposed. Improper handling of
the OLPF modules or camera during this procedure may compromise the installation or cause irreparable damage to
your camera or sensor.
WARNING:
DO NOT allow any dirt or debris to enter the optical cavity.
WARNING:
Use only VV OLPFs. DO NOT use other OLPFs.
SWAP AN INTERCHANGEABLE OLPF
REQUIRED TOOL(S):
T20 TORX driver
1. Turn off the camera.
2. Remove any cables or accessories that may interfere with operations.
3. Loosen and remove the four (4) M4x0.7 x 8 mm lens mount screws in a cross pattern (“X” pattern) using a T20
TORX driver.
NOTE:
Some lens mounts have captive screws that are not removable.
NOTE:
Screw removal may require a large handle T20 TORX driver and additional leverage.
4. Remove the lens mount.
5. Use a damp, lint-free cloth to gently wipe down the area around the lens mount and OLPF module. Remove as
much dust and debris as possible.
6. Use a T20 TORX driver to turn the OLPF lock on the camera counter-clockwise by a third turn to the Unlock
position. DO NOT turn the indicator mark past the Unlock icon.
WARNING:
DO NOT OVERTIGHTEN.
7. Remove the OLPF module and place it in its protective case.
8. Use an LED light to ensure that the optical cavity is clean and free from dust or debris.
9. Ensure the new OLPF module is clean and free of debris.
10. Install the new OLPF module straight into the optical cavity, keeping the front face of the OLPF module parallel to
the front of the camera.
NOTE:
Inserting the OLPF module at an angle may cause it to not seat properly.
11. Use a T20 TORX driver to turn the OLPF lock on the camera clockwise by a third turn to the Lock position. DO
NOT turn the indicator mark past the Lock icon.
WARNING:
DO NOT OVERTIGHTEN.
NOTE:
If the lock does not turn easily, gently press down on the OLPF module while turning the lock.
12. Replace the lens mount.
13. Replace and loosely tighten the four (4) M4x0.7 x 8 mm lens mount screws in a cross pattern (“X” pattern) using a
T20 TORX driver. DO NOT FULLY TIGHTEN.
NOTE:
Some lens mounts have captive screws that are not removable.
14. Fully tighten the four (4) lens mount screws in a cross pattern (“X” pattern) using a T20 TORX driver. DO NOT
exceed 350 in-oz, or damage may occur.
WARNING:
DO NOT OVERTIGHTEN.
C O PYR I G HT © 2 0 1 9 R ED.C O M , LLC
9 5 5 - 0 1 8 4 _V 7 .2 , R EV - D
|
4 0
RED RANGER OPERATION GUIDE
Содержание MONSTRO 8K VV
