background image

-1-

Inside US: +1 (877) 432-9908 

 

Bulletin No. PAXLCR-C

Outside US: +1 (717) 767-6511 

 

Drawing No. LP0749

www.redlion.net 

 

Released 2018-01-16

3.60 (91.4)

(96.5)

3.80

1.95

(49.5)

(2.5)

.10

(104.1)

4.10

(44.5)

1.75

PAR

9

1

3

2

4 5

6 7 8

10

13

11 12

14 15

SEL

RST

P

S 1

P

S 2

A

B

GENERAL DESCRIPTION

The PAXLCR is a versatile meter that provides a single or dual counter 

with rate indication, scaling and dual relay outputs. The 6-digit display 

has 0.56" high digits with adjustable display intensity. The display can be 

toggled manually or automatically between the selected counter and rate 

values.

The meter has two signal inputs and a choice of eight different count 

modes. These include bi-directional, quadrature and anti-coincidence 

counting, as well as a dual counter mode. When programmed as a Dual 

Counter, each counter has separate scaling and decimal point selection.

Rate indication is available in all count modes. The Rate Indicator has 

separate scaling and decimal point selection, along with programmable 

display update times. In addition to the signal inputs, the User Input can 

be programmed to perform a variety of meter control functions.

Two setpoint outputs are provided, each with a Form C relay. The 

outputs can activate based on either counter or rate setpoint values. An 

internal batch counter can be used to count setpoint output activations.

The PAXLCR can be powered from a wide range of AC or DC 

voltages. The meter has been specifically designed for harsh industrial 

environments. With a NEMA 4X/IP65 sealed bezel and extensive testing 

to meet CE requirements, the meter provides a tough yet reliable 

application solution.

ORDERING INFORMATION

MODEL NO. DESCRIPTION

PART NUMBER

PAXLCR

Dual Counter & Rate Meter with Dual Relay Output

PAXLCR00

PAXLCRU UL Listed Dual Counter & Rate Meter with Dual 

Relay Output

PAXLCRU0

SAFETY SUMMARY

All safety regulations, local codes and instructions that appear in this 

and corresponding literature, or on equipment, must be observed to 

ensure personal safety and to prevent damage to either the instrument or 

equipment connected to it. If equipment is used in a manner not specified 

by the manufacturer, the protection provided by the equipment may be 

impaired. Do not use this meter to directly command motors, valves, or 

other actuators not equipped with safeguards. To do so can be potentially 

harmful to persons or equipment in the event of a fault to the meter.

SPECIFICATIONS

1. 

DISPLAY

: 6 digit, 0.56" (14.2 mm) intensity adjustable Red LED

2. 

POWER REQUIREMENTS

:

AC POWER: 50 to 250 VAC 50/60 Hz, 12 VA

Isolation: 2300 Vrms for 1 min. to all inputs and outputs

DC POWER: 21.6 to 250 VDC, 6 W

DC Out: +24 VDC @ 100 mA if input voltage is greater than 50 VAC/VDC

  +24 VDC @ 50 mA if input voltage is less than 50 VDC

3. 

COUNTER DISPLAYS

:

Counter A: 6-digits, enabled in all count modes

Display Designator: “A” to the left side of the display

Display Range: -99999 to 999999

Counter B: 6-digits, enabled in Dual Count mode or Batch Counter

Display Designator: “B” to the left side of the display

Display Range: 0 to 999999 (positive count only)

Overflow Indication: Display “



” alternates with overflowed count value

Maximum Count Rates: 50% duty cycle, count mode dependent.

Model PAXLCR - PAX Lite Dual Counter and Rate Meter

DIMENSIONS  In inches (mm)

CAUTION: Risk of Danger.

Read complete instructions prior to 

installation and operation of the unit.

CAUTION: 

Risk of electric shock.

Note: Recommended minimum clearance (behind the panel) for mounting clip installation is 

 

 2.1" (53.4) H x 5.0" (127) W.

For Model No. PAXLCRU0 Only

  6 DIGIT, 0.56" HIGH RED LED DISPLAY

  PROGRAMMABLE SCALING FOR COUNT AND RATE

  BI-DIRECTIONAL COUNTING, UP/DOWN CONTROL

  QUADRATURE SENSING (UP TO 4 TIMES RESOLUTION)

  BUILT-IN BATCH COUNTING CAPABILITY

  PROGRAMMABLE USER INPUT

  DUAL 5 AMP FORM C RELAYS

  UNIVERSALLY POWERED

  NEMA 4X/IP65 SEALED FRONT BEZEL

C

US LISTED

UL

R

PROC. CONT. EQ.

E179259

Содержание PAX Lite PAXLCR














Отзывы: