Installation 8DI/RO - A
Drawing No. LP1119
Effective 02/2020
DA 8 Digital Input / 8 Relay Output Module
Installation Guide
1
FOR USE IN HAZARDOUS LOCATIONS:
Class I, Division 2, Groups A, B, C, and D
T4
C
US
UL
R
LISTED
IND.CONT. EQ.
E317425
MODULE PACKAGE CHECKLIST
This product package should contain the items listed below. If
any items are missing or damaged, contact Red Lion immediately.
- DIN Rail Mount DA 8DI/8RO Module
- Installation Guide
GENERAL DESCRIPTION
The DA 8DI/8RO module is designed for use with the DA70
controllers, that can support up to 10 I/O modules simultaneously.
This module features 8 Digital Inputs and 8 Relay Outputs that
can be used to monitor contact or sensor inputs and actuate
relays, solenoids, PLC inputs, etc.
The inputs accept standard DC inputs or contact closures, and
are configured for Sink/Source signals via software switches.
Additionally, each input has a switch selectable input filter that
can be used to prevent contact bounce. Each input may also be
software configured as a high-active or low-active input.
The module is available with relay outputs that are capable of
switching up to one amp each. For applications requiring large
loads to be controlled, several DIN rail mount relays are available.
The modules connect and communicate via proprietary
backplane to the DA host device. The DA host device, equipped
with serial ports as well as an Ethernet port(s), allows the system
to share data with PCs, PLCs, and SCADA systems.
Internal power management circuits allow the module to be
replaced while power is applied, which reduces downtime in the
event of a module failure. All configuration information is stored
locally within the module, as well as in the Host, so replacement
modules do not need to be configured.
DIMENSIONS In Inches (mm)
CONFIGURATION
The DA 8DI/8RO modules are configured with Windows
®
compatible Crimson
®
software. The software is an easy to use,
graphical interface which provides a means of configuration and
commissioning of new systems, as well as routine module
re-calibration.
SAFETY SUMMARY
All safety related regulations, local codes and instructions that
appear in this document or on equipment must be observed to
ensure personal safety and to prevent damage to either the
device or equipment connected to it.
Do not use these products to replace proper safety interlocking.
No software-based device (or any other solid-state device) should
ever be designed to be responsible for the maintenance of
personnel safety or consequential equipment not equipped with
safeguards. Red Lion disclaims any responsibility for damages,
either direct or consequential, that result from the use of this
equipment in a manner not specified.
0.49
(12.51)
0.45 (11.50)
4.53 (114.97)
6.22
(157.91)
1.91
(48.51)
1.35
(34.32)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
09
08
07
06
05
04
03
02
01
6.00
(152.40)
CAUTION: Risk of Danger
Read complete instructions prior to installation and
operation of the unit.
ATTENTION : Risque de danger
Lire les instructions complètes avant l’installation et
l’utilisation de l’appareil.
WARNING - EXPLOSION HAZARD - SUBSTITUTION
OF COMPONENTS MAY IMPAIR SUITABILITY FOR
CLASS I, DIVISION 2
AVERTISSEMENT - DANGER D’EXPLOSION - LE
REMPLACEMENT DE COMPOSANTS PEUT NUIRE À
L’APTITUDE À LA CLASSE I, DIVISION 2
This equipment is suitable for use in Class I, Division 2,
Groups A, B, C, D, or non-hazardous locations only.
Cet équipement est adapté à une utilisation dans des
endroits de classe I, Division 2, Groupes A, B, C, D, ou
dans des endroits non dangereux seulement.
z
Adds I/O capability to the DA70
z
Offers complete isolation; inputs, power and Controller
z
Inputs independently software selectable for sink or source
signals, high or low active states, and high or low frequency
signals
z
Ideal for data acquisition applications
z
Configured using Crimson
®
software (version 3.1 or later)
