RectorSeal AG-1250E Скачать руководство пользователя страница 1

Installation Instructions:

 

Standard HVAC Installation w/ optional external alarm or accessory

INSTALLATION OF SENSOR:

(To ensure proper performance of product, instructions must be followed.)

1. Clean desired mounting surface thoroughly with included alcohol pad.

2. Using the double sided tape, affix the mounting clip to the desired surface in pan. Next, snap AG-1250E to mounting clip.

24 VAC, 1 Amp Relay Normally Open      

24 VAC, 5 Amps Relay Normally Closed

AG1250E 30072012 A L H 0

Moisture detection LED

Metal contacts

Mounting Clip

AG-1250E

Work  Safe,  READ  THIS!

ATTENTION

: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING INSTALLATION 

MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.

STOP/READ:

 The AG-1250E must be installed in accordance with manufacturer’s instructions. The AG-1250E must be installed in accordance with all applicable 

local plumbing, drainage and electrical codes.

WARNING:

 Remove electrical shock hazard – 

DISCONNECT THE POWER TO THE HVAC UNIT BEFORE INSTALLING THE AQUAGUARD AG-1250E 

to 

avoid electrical shock and/or equipment damage. Do not use on circuits exceeding 24 VAC to avoid damage to sensor, shock or fire hazard.

CAUTION: 

In some situations the sensor may cause the unit to rapidly cycle on and off as water level rises slowly in pan. After a brief period the HVAC unit will 

turn off completely. Condensation drain must be serviced if this occurs.

CAUTION:

 In any installation where property damage and/or personal injury might result from an inoperative sensor due to power outages, a back-up system(s) 

and /or alarm should be installed.

NOTICE:

 The AG-1250E must only be installed by a licensed contractor. Condensation pan must be properly maintained after installation and be kept free of 

foreign matter, rust or other obstructions that might interfere with the proper operation of the AG-1250E.

NOTICE: Cleaning solutions or dirty probes may not allow the HVAC unit to come on. If such, remove probe sensor and/or secondary pan sensor, clean, and dry.

WIRING THE AG-1250E:

 

(To ensure proper performance of product, instructions must be followed.)

1. Ensure the power is disconnected to the HVAC unit at the main electrical panel prior to moving to step 2. Refer to the appliance manufacturer’s installation

and operating instructions and also review the wiring diagram in their instructions.

For Breaking “Wall Thermostat” Power Wire (see Figure 1)

2.  In HVAC Unit locate 24 VAC Power wire going to “Wall Thermostat”, (Typically RED). Break/Disconnect 24 VAC Power wire going to “Wall Thermostat”. 

A.  Connect “RED”, “Input: 24 VAC (Hot)” wire of AG-1250E to 24 VAC (Hot) secondary side of 24 VAC Transformer.

B.  Connect “PURPLE”, “Normally Closed” wire of AG-1250E to Thermostat’s “R” Terminal. 

NOTE: “PURPLE” wire must be connected to “THERMOSTAT”. Maximum capacity 24VAC/5Amp.

C.  Connect “BLACK”, “Input: 24 VAC (Common)” wire of AG-1250E to 24 VAC (COMMON) secondary side of 24 VAC Transformer or Thermostat’s  

  “C” Terminal.

D.  “WHITE”, “Normally Open” wire of AG-1250E must be connected to AquaGuard, AG-9100 External Alarm  (see Figure 1) or Home Alarm System,  

or Communicating System, etc..

CAUTION:  “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
Note: When AG-1250E is wired correctly, the HVAC unit will shut-off upon condensate detection.

Optional Wiring:  For Breaking Compressor Wire 

3.  In HVAC Unit locate “Compressor wire going to “Wall Thermostat”, typically (YELLOW). Break/Disconnect Compressor wire going to “Wall Thermostat”.

A.  Connect typically “YELLOW” wire, going to “Wall Thermostat” to “RED”, “Input: 24 VAC (Hot)” wire of AG-1250E .

B.  Connect “PURPLE”, “Normally Closed” wire of AG-1250E to Compressor’s typically “YELLOW” wire going to Compressor. 

NOTE: “PURPLE” wire must be connected to COMPRESSOR  “YELLOW” Wire. Maximum capacity 24VAC/5Amp.

C.  Connect “BLACK”, “Input: 24 VAC (Common)” wire of AG-1250E to 24 VAC (COMMON) secondary side of 24 VAC Transformer or Thermostat’s  

  “C” Terminal.

D.  “WHITE”, “Normally Open” wire of AG-1250E must be connected to AquaGuard, AG-9100 External Alarm  (see Figure 1) or Home Alarm System,  

or Communicating System, etc..

CAUTION:  “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
Note: When the AG-1250E is wired correctly, (ONLY) the Compressor will shut-off upon condensate detection. Air Handler will continue to run.

4. Test the AG-1250E Secondary Pan Sensor (At start-up check initial amperage load) while the HVAC unit is on and functioning correctly. See installation of

the AG-1250E: 

HVAC

AG-1250E

24 VAC, 

5.0 Amps Carry

Figure 1

Normally Op

en WH

ITE

Normalmente abi

erto - BL

ANCO

AG-1250E

24 VAC, 

5.0 Amps Carry

No

rm

all

y C

los

ed

 - 

PU

RP

LE

Tra

nsf

orm

ad

or 

ca

lie

nte

 - R

OJ

O

4. Test sensor: Place sensor in secondary pan and add enough water to the pan to cover contacts (approximately ¼ inch). LED will illuminate and HVAC

    unit will stop running if wired correctly

LIMITED WARRANTIES AND LIMITATION OF 

LIABILITY

REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com

1 YEAR SWITCH AND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY

The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.

Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from 

defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the 

one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and 

CONDITIONS set forth below. 
EXCLUSIONS

This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-

ONDARY DRAIN PAN LIMITED WARRANTY AND LIMITATION OF LIABILITY

This warranty applies only to secondary drain pans installed in the United States and Canada.

Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from 

defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace 

models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date 

of

purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This 

warranty extends only to the original consumer purchaser and is nontransferable. 
EXCLUSIONS

This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and 

petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.

GENERAL TERMS AND CONDITIONS

To be eligible for the warranty the purchaser must provide Rectorseal with the following:

1. Proof of Purchase (Original Receipt)

2. Installer’s Testimony

3. Original Product

4. Original Work Order

5. Photos of Installation

PURCHASER  MUST  PAY ALL LABOR AND SHIPPING  CHARGES NECESSARY  TO REPLACE  PRODUCT  COVERED BY  THIS WAR-

RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject 

to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor 

moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures 

caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-

fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently 

take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 

thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-

fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This 

will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration, 

the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a 

recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no 

liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY  SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE

PAID FOR THE PRODUCT ALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction. 

Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility 

under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects 

and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be 

the responsibility of Rectorseal. RECTORSEAL SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT 

DAMAGES WHATSOEVER TO THE PURCHASER OR ANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN 

LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL  NOT EXTEND BEYOND THE DURATION OF THE APPLICA-

BLE EXPRESSED WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied 

warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also 

have

 other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be 

commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the 

State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA

RectorSeal® Houston, TX USA      www.rectorseals.com     US Patent Pending   

Installation Instructions:

 

Standard HVAC Installation w/ optional external alarm or accessory

INSTALLATION OF SENSOR:

(To ensure proper performance of product, instructions must be followed.)

1. Clean desired mounting surface thoroughly with included alcohol pad.

2. Using the double sided tape, affix the mounting clip to the desired surface in pan. Next, snap AG-1250E to mounting clip.

24 VAC, 1 Amp Relay Normally Open      

24 VAC, 5 Amps Relay Normally Closed

AG1250E 30072012 A L H 0

Moisture detection LED

Metal contacts

Mounting Clip

AG-1250E

Work  Safe,  READ  THIS!

ATTENTION

: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING INSTALLATION 

MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.

STOP/READ:

 The AG-1250E must be installed in accordance with manufacturer’s instructions. The AG-1250E must be installed in accordance with all applicable 

local plumbing, drainage and electrical codes.

WARNING:

 Remove electrical shock hazard – 

DISCONNECT THE POWER TO THE HVAC UNIT BEFORE INSTALLING THE AQUAGUARD AG-1250E 

to 

avoid electrical shock and/or equipment damage. Do not use on circuits exceeding 24 VAC to avoid damage to sensor, shock or fire hazard.

CAUTION: 

In some situations the sensor may cause the unit to rapidly cycle on and off as water level rises slowly in pan. After a brief period the HVAC unit will 

turn off completely. Condensation drain must be serviced if this occurs.

CAUTION:

 In any installation where property damage and/or personal injury might result from an inoperative sensor due to power outages, a back-up system(s) 

and /or alarm should be installed.

NOTICE:

 The AG-1250E must only be installed by a licensed contractor. Condensation pan must be properly maintained after installation and be kept free of 

foreign matter, rust or other obstructions that might interfere with the proper operation of the AG-1250E.

NOTICE: Cleaning solutions or dirty probes may not allow the HVAC unit to come on. If such, remove probe sensor and/or secondary pan sensor, clean, and dry.

WIRING THE AG-1250E:

 

(To ensure proper performance of product, instructions must be followed.)

1. Ensure the power is disconnected to the HVAC unit at the main electrical panel prior to moving to step 2. Refer to the appliance manufacturer’s installation

and operating instructions and also review the wiring diagram in their instructions.

For Breaking “Wall Thermostat” Power Wire (see Figure 1)

2.  In HVAC Unit locate 24 VAC Power wire going to “Wall Thermostat”, (Typically RED). Break/Disconnect 24 VAC Power wire going to “Wall Thermostat”. 

A.  Connect “RED”, “Input: 24 VAC (Hot)” wire of AG-1250E to 24 VAC (Hot) secondary side of 24 VAC Transformer.

B.  Connect “PURPLE”, “Normally Closed” wire of AG-1250E to Thermostat’s “R” Terminal. 

NOTE: “PURPLE” wire must be connected to “THERMOSTAT”. Maximum capacity 24VAC/5Amp.

C.  Connect “BLACK”, “Input: 24 VAC (Common)” wire of AG-1250E to 24 VAC (COMMON) secondary side of 24 VAC Transformer or Thermostat’s  

  “C” Terminal.

D.  “WHITE”, “Normally Open” wire of AG-1250E must be connected to AquaGuard, AG-9100 External Alarm  (see Figure 1) or Home Alarm System,  

or Communicating System, etc..

CAUTION:  “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
Note: When AG-1250E is wired correctly, the HVAC unit will shut-off upon condensate detection.

Optional Wiring:  For Breaking Compressor Wire 

3.  In HVAC Unit locate “Compressor wire going to “Wall Thermostat”, typically (YELLOW). Break/Disconnect Compressor wire going to “Wall Thermostat”.

A.  Connect typically “YELLOW” wire, going to “Wall Thermostat” to “RED”, “Input: 24 VAC (Hot)” wire of AG-1250E .

B.  Connect “PURPLE”, “Normally Closed” wire of AG-1250E to Compressor’s typically “YELLOW” wire going to Compressor. 

NOTE: “PURPLE” wire must be connected to COMPRESSOR  “YELLOW” Wire. Maximum capacity 24VAC/5Amp.

C.  Connect “BLACK”, “Input: 24 VAC (Common)” wire of AG-1250E to 24 VAC (COMMON) secondary side of 24 VAC Transformer or Thermostat’s  

  “C” Terminal.

D.  “WHITE”, “Normally Open” wire of AG-1250E must be connected to AquaGuard, AG-9100 External Alarm  (see Figure 1) or Home Alarm System,  

or Communicating System, etc..

CAUTION:  “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
Note: When the AG-1250E is wired correctly, (ONLY) the Compressor will shut-off upon condensate detection. Air Handler will continue to run.

4. Test the AG-1250E Secondary Pan Sensor (At start-up check initial amperage load) while the HVAC unit is on and functioning correctly. See installation of

the AG-1250E: 

HVAC

AG-1250E

24 VAC, 

5.0 Amps Carry

Figure 1

Normally Op

en WH

ITE

Normalmente abi

erto - BL

ANCO

AG-1250E

24 VAC, 

5.0 Amps Carry

No

rm

all

y C

los

ed

 - 

PU

RP

LE

Tra

nsf

orm

ad

or 

ca

lie

nte

 - R

OJ

O

4. Test sensor: Place sensor in secondary pan and add enough water to the pan to cover contacts (approximately ¼ inch). LED will illuminate and HVAC

    unit will stop running if wired correctly

LIMITED WARRANTIES AND LIMITATION OF 

LIABILITY

REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com

1 YEAR SWITCH AND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY

The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.

Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from 

defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the 

one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and 

CONDITIONS set forth below. 
EXCLUSIONS

This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-

ONDARY DRAIN PAN LIMITED WARRANTY AND LIMITATION OF LIABILITY

This warranty applies only to secondary drain pans installed in the United States and Canada.

Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from 

defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace 

models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date 

of

purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This 

warranty extends only to the original consumer purchaser and is nontransferable. 
EXCLUSIONS

This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and 

petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.

GENERAL TERMS AND CONDITIONS

To be eligible for the warranty the purchaser must provide Rectorseal with the following:

1. Proof of Purchase (Original Receipt)

2. Installer’s Testimony

3. Original Product

4. Original Work Order

5. Photos of Installation

PURCHASER  MUST  PAY ALL LABOR AND SHIPPING  CHARGES NECESSARY  TO REPLACE  PRODUCT  COVERED BY  THIS WAR-

RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject 

to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor 

moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures 

caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-

fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently 

take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 

thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-

fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This 

will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration, 

the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a 

recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no 

liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY  SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE

PAID FOR THE PRODUCT ALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction. 

Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility 

under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects 

and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be 

the responsibility of Rectorseal. RECTORSEAL SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT 

DAMAGES WHATSOEVER TO THE PURCHASER OR ANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN 

LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL  NOT EXTEND BEYOND THE DURATION OF THE APPLICA-

BLE EXPRESSED WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied 

warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also 

have

 other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be 

commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the 

State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA

RectorSeal® Houston, TX USA      www.rectorseals.com     US Patent Pending   

LIMITED WARRANTIES AND LIMITATION OF 

LIABILITY

REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com

1 YEAR SWITCH AND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY

The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.

Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from 

defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the 

one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and 

CONDITIONS set forth below. 
EXCLUSIONS

This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-

ONDARY DRAIN PAN LIMITED WARRANTY AND LIMITATION OF LIABILITY

This warranty applies only to secondary drain pans installed in the United States and Canada.

Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from 

defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace 

models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date 

of

purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This

warranty extends only to the original consumer purchaser and is nontransferable. 
EXCLUSIONS

This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and 

petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.

GENERAL TERMS AND CONDITIONS

To be eligible for the warranty the purchaser must provide Rectorseal with the following:

1. Proof of Purchase (Original Receipt)

2. Installer’s Testimony

3. Original Product

4. Original Work Order

5. Photos of Installation

PURCHASER  MUST  PAY ALL LABOR AND SHIPPING  CHARGES NECESSARY  TO REPLACE  PRODUCT  COVERED BY  THIS WAR-

RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject 

to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor 

moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures 

caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-

fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently 

take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 

thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-

fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This 

will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration, 

the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a 

recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no 

liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY  SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE

PAID FOR THE PRODUCT ALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction. 

Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility 

under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects 

and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be 

the responsibility of Rectorseal. RECTORSEAL SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT 

DAMAGES WHATSOEVER TO THE PURCHASER OR ANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN 

LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL  NOT EXTEND BEYOND THE DURATION OF THE APPLICA-

BLE EXPRESSED WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied 

warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also 

have

 other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be 

commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the 

State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA

RectorSeal® Houston, TX USA      www.rectorseals.com     US Patent Pending   

In HVAC Unit locate H

A. Connect “RED”, “Input 24 VAC (Hot)” and “Gray” “Common” wire of  AG-1250E to 24 

VAC (Hot) secondary side of  24 VAC Transformer.

   

   

   

   

   

   

   

   

  C

om

ún

 -

 G

R

IS

C

om

m

on

 -

 G

R

AY

*Note: 

Probe Wire Not Included

On Model AG-1250E

Figure 1

NOTE: When AG-1250E is wired correctly, the HVAC unit will shut-off upon condensate 

detection.

AG-1250E to 

AG-1250E to 

AG-1250E

AG-1250E

wire

.

D. Optional: Connect “WHITE”, “Normally Open” wire of AG-1250E to the “WHITE” wire of 

AquaGuard, AG-9100 External Alarm or Home Alarm System, or Communicating System, etc...

In HVAC Unit locate H

Installation Instructions:

 

Standard HVAC Installation w/ optional external alarm or accessory

INSTALLATION OF SENSOR:

(To ensure proper performance of product, instructions must be followed.)

1. Clean desired mounting surface thoroughly with included alcohol pad.

2. Using the double sided tape, affix the mounting clip to the desired surface in pan. Next, snap AG-1250E to mounting clip.

24 VAC, 1 Amp Relay Normally Open      

24 VAC, 5 Amps Relay Normally Closed

AG1250E 30072012 A L H 0

Moisture detection LED

Metal contacts

Mounting Clip

AG-1250E

Work  Safe,  READ  THIS!

ATTENTION

: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING INSTALLATION 

MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.

STOP/READ:

 The AG-1250E must be installed in accordance with manufacturer’s instructions. The AG-1250E must be installed in accordance with all applicable 

local plumbing, drainage and electrical codes.

WARNING:

 Remove electrical shock hazard – 

DISCONNECT THE POWER TO THE HVAC UNIT BEFORE INSTALLING THE AQUAGUARD AG-1250E 

to 

avoid electrical shock and/or equipment damage. Do not use on circuits exceeding 24 VAC to avoid damage to sensor, shock or fire hazard.

CAUTION: 

In some situations the sensor may cause the unit to rapidly cycle on and off as water level rises slowly in pan. After a brief period the HVAC unit will 

turn off completely. Condensation drain must be serviced if this occurs.

CAUTION:

 In any installation where property damage and/or personal injury might result from an inoperative sensor due to power outages, a back-up system(s) 

and /or alarm should be installed.

NOTICE:

 The AG-1250E must only be installed by a licensed contractor. Condensation pan must be properly maintained after installation and be kept free of 

foreign matter, rust or other obstructions that might interfere with the proper operation of the AG-1250E.

NOTICE: Cleaning solutions or dirty probes may not allow the HVAC unit to come on. If such, remove probe sensor and/or secondary pan sensor, clean, and dry.

WIRING THE AG-1250E:

 

(To ensure proper performance of product, instructions must be followed.)

1. Ensure the power is disconnected to the HVAC unit at the main electrical panel prior to moving to step 2. Refer to the appliance manufacturer’s installation

and operating instructions and also review the wiring diagram in their instructions.

For Breaking “Wall Thermostat” Power Wire (see Figure 1)

2.  In HVAC Unit locate 24 VAC Power wire going to “Wall Thermostat”, (Typically RED). Break/Disconnect 24 VAC Power wire going to “Wall Thermostat”. 

A.  Connect “RED”, “Input: 24 VAC (Hot)” wire of AG-1250E to 24 VAC (Hot) secondary side of 24 VAC Transformer.

B.  Connect “PURPLE”, “Normally Closed” wire of AG-1250E to Thermostat’s “R” Terminal. 

NOTE: “PURPLE” wire must be connected to “THERMOSTAT”. Maximum capacity 24VAC/5Amp.

C.  Connect “BLACK”, “Input: 24 VAC (Common)” wire of AG-1250E to 24 VAC (COMMON) secondary side of 24 VAC Transformer or Thermostat’s  

  “C” Terminal.

D.  “WHITE”, “Normally Open” wire of AG-1250E must be connected to AquaGuard, AG-9100 External Alarm  (see Figure 1) or Home Alarm System,  

or Communicating System, etc..

CAUTION:  “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
Note: When AG-1250E is wired correctly, the HVAC unit will shut-off upon condensate detection.

Optional Wiring:  For Breaking Compressor Wire 

3.  In HVAC Unit locate “Compressor wire going to “Wall Thermostat”, typically (YELLOW). Break/Disconnect Compressor wire going to “Wall Thermostat”.

A.  Connect typically “YELLOW” wire, going to “Wall Thermostat” to “RED”, “Input: 24 VAC (Hot)” wire of AG-1250E .

B.  Connect “PURPLE”, “Normally Closed” wire of AG-1250E to Compressor’s typically “YELLOW” wire going to Compressor. 

NOTE: “PURPLE” wire must be connected to COMPRESSOR  “YELLOW” Wire. Maximum capacity 24VAC/5Amp.

C.  Connect “BLACK”, “Input: 24 VAC (Common)” wire of AG-1250E to 24 VAC (COMMON) secondary side of 24 VAC Transformer or Thermostat’s  

  “C” Terminal.

D.  “WHITE”, “Normally Open” wire of AG-1250E must be connected to AquaGuard, AG-9100 External Alarm  (see Figure 1) or Home Alarm System,  

or Communicating System, etc..

CAUTION:  “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
Note: When the AG-1250E is wired correctly, (ONLY) the Compressor will shut-off upon condensate detection. Air Handler will continue to run.

4. Test the AG-1250E Secondary Pan Sensor (At start-up check initial amperage load) while the HVAC unit is on and functioning correctly. See installation of

the AG-1250E: 

HVAC

AG-1250E

24 VAC, 

5.0 Amps Carry

Figure 1

Normally Op

en WH

ITE

Normalmente abi

erto - BL

ANCO

AG-1250E

24 VAC, 

5.0 Amps Carry

No

rm

all

y C

los

ed

 - 

PU

RP

LE

Tra

nsf

orm

ad

or 

ca

lie

nte

 - R

OJ

O

4. Test sensor: Place sensor in secondary pan and add enough water to the pan to cover contacts (approximately ¼ inch). LED will illuminate and HVAC

    unit will stop running if wired correctly

LIMITED WARRANTIES AND LIMITATION OF 

LIABILITY

REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com

1 YEAR SWITCH AND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY

The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.

Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from 

defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the 

one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and 

CONDITIONS set forth below. 
EXCLUSIONS

This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-

ONDARY DRAIN PAN LIMITED WARRANTY AND LIMITATION OF LIABILITY

This warranty applies only to secondary drain pans installed in the United States and Canada.

Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from 

defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace 

models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date 

of

purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This 

warranty extends only to the original consumer purchaser and is nontransferable. 
EXCLUSIONS

This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and 

petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.

GENERAL TERMS AND CONDITIONS

To be eligible for the warranty the purchaser must provide Rectorseal with the following:

1. Proof of Purchase (Original Receipt)

2. Installer’s Testimony

3. Original Product

4. Original Work Order

5. Photos of Installation

PURCHASER  MUST  PAY ALL LABOR AND SHIPPING  CHARGES NECESSARY  TO REPLACE  PRODUCT  COVERED BY  THIS WAR-

RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject 

to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor 

moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures 

caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-

fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently 

take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 

thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-

fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This 

will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration, 

the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a 

recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no 

liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY  SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE

PAID FOR THE PRODUCT ALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction. 

Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility 

under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects 

and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be 

the responsibility of Rectorseal. RECTORSEAL SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT 

DAMAGES WHATSOEVER TO THE PURCHASER OR ANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN 

LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL  NOT EXTEND BEYOND THE DURATION OF THE APPLICA-

BLE EXPRESSED WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied 

warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also 

have

 other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be 

commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the 

State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA

RectorSeal® Houston, TX USA      www.rectorseals.com     US Patent Pending   

Отзывы: