manualshive.com logo in svg

Record C 127 SU OFFSET, Руководство пользователя

Поделиться
Скачать
Record C 127 SU OFFSET Скачать руководство пользователя страница 21

Operation

5

BAL_C127-SU_OFFSET_EN_1V0_REC_121-006454770

21 / 32

Reset control panel

Step

Button

Operation

Function

Display on LCD

1.

E

Press button for 12 seconds

Perform control panel reset

2.

3.

The connection has been established

DFA 127 V2.21

Basic operator

5.1.3

Display system information

Information about the door system, such as software version, door type, or servicing status, can be
shown on the display.

NOTICE

The main view is returned to by scrolling or automatically after 20 seconds.

Step

Button

Operation

Function

1.

E

Press button for approx.

2 seconds

Software information

is displayed

STA20 V2.0

BDE-D V2.05 1

Software

2.

E

Press button 1 x

Scroll through the in-

formation and/or re-

turn to main view

STA20 V2.0

BDE-D V2.05 1

Software

3.

E

Press button 1 x

Scroll through the in-

formation and/or re-

turn to main view

Servicing

0

50

100

5.2

Parameter overview

Factory settings: 

Basic operator

 (Full Power)

NOTICE

Parameterization of the swing door operator can only be carried out with the optional elec-
tronic BDE-D, the App i-record or the service and flash programmer FPC 902 or the test box.

NOTICE

Please always leave the parameter list in the drive even when replacing the STG!

Содержание C 127 SU OFFSET

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды