manualshive.com logo in svg

Record C 127 SU OFFSET, Руководство пользователя

Поделиться
Скачать
Record C 127 SU OFFSET Скачать руководство пользователя страница 20

5

Operation

20 / 32

BAL_C127-SU_OFFSET_EN_1V0_REC_121-006454770

Sub menu

NOTICE

The main menu is returned to automatically 3 minutes after the last entry.

Button

Name

Operation

Function

Display on LCD

E

Enter button

Press button 1 x to go to
the next sub menu.

Select menu item, confirm
entry

Opening speed

0

10 20 30 40

+

Plus button

Press button 1 x to go
down.

Navigate downwards in the
menu

Parameter

Driving cycle

Time delay open
Operator

Press button 1 x to increase
the value.

Move the slide control to
the right to increase the
value

Closing speed

0

10 20 30 40

-

Minus button

Press button 1 x to go up.

Navigate upwards in the
menu

Parameter

Driving cycle

Time delay open

Operator

Press button 1 x to reduce
the value.

Move the slide control to
the left to reduce the value

Closing speed

0

10 20 30 40

C

Clear button

Press button 1 x to go to
the previous menu.

Leave the menu item
without saving.

Parameter

Driving cycle

Time delay open
Operator

5.1.2

Perform reset

Reset controller

Step

Button

Operation

Function

Display on LCD

1.

E

Press button for 5 seconds

Perform controller reset

No

Reset controller?

Yes

2.

C

Press button 1 x

Cancel reset

E

Press button 1 x

Perform reset

Содержание C 127 SU OFFSET

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды