manualshive.com logo in svg

ReBach CATCH VCO-A DIY, Инструкция по сборке

Поделиться
Скачать
ReBach CATCH VCO-A DIY Скачать руководство пользователя страница 1

Date:

11-04-20

Project:

Remark: 

File:

RBDIY-CTSVCOA-1.1

Version:

1.2

Title: 

CATCH VCO-A DIY

HW version:

1.1

REF: 

Page:

1 

- 1x Main PCBA RB1815
- 1x Front PCB RB1816
- 2x 10K Pot-meter
- 1x 50K Pot-meter
- 2x 10K trimmer
- 3x M7 Washer
- 3x M7 Nut
- 6x 3.5mm Jack incl nut

Note: 

Note: 

Assembly instruction

Thank you for purchasing this ReBach DIY Voltage-controlled Oscillator ! 

We hope you enjoy the construction and use of this beautiful VCO.

Package Content: 

- 3x Knob White 
- 3x Knob cab 
- 1x Ribbon power cable 
- 2x 3mm screw

Check if all the above-mentioned parts are present in the packaging before starting construction! Contact
your supplier if a part is missing before you start building.

You the customer agree that if the packaging has been opened and some construction steps have been

made, you are responsible for a successful construction.

Follow the steps in this building instructions carefully to prevent errors

The conditions of your supplier are respected by ReBach!

No rights can be deducted from this document.

© 2020 ReBach  –  

www.rebach.eu

Содержание CATCH VCO-A DIY








Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды