STORE MORE BINDER NOOK™ INSTRUCTIONS - 2, 4 and 6-Shelf Units
6-SHELF ASSEMBLY INSTRUCTIONS
Your 6-Shelf Unit is made up of a Store More Binder Nook™
2-Shelf Base Unit and two 2-Shelf Add-On Units.
STEP THIRTEEN:
Assemble the 4-Shelf Unit following the previous directions
on pages 2-3 from Step 1 through Step 11, substituting Item
#8A for #8 in Step 11. Set aside #8, and complete Step 12.
STEP FOURTEEN:
Install the remaining item #13 studs (included in the
hardware package for the 2-Shelf Add-On Unit into the four
holes marked “Y” located at the top of your 4-Shelf Binder
Nook—refer to diagram.)
STEP FIFTEEN:
Place the 2-Shelf Add-On Unit on the top of the 4-Shelf Unit
and tighten the four locking cams. The locking cams must be
locked into position by turning them a full 180 degrees with
the assembly tool.
Item 8
Item 10
Item 6
Item 9
X
X
X
X
~ IMPORTANT NOTICE ~
Your Store More Binder Nook
™
is now assembled and must be
attached to a wall. This step is very important as your Binder Nook
could be pulled over, causing bodily injury to a child or adult.
Before you start:
Position your assembled Binder Nook in the corner
of the room you have selected.
Using an electric drill, drill directly through the mounting holes of the
Binder Nook into the wall. The diameter of the hole should be 1/4".
Drill deep enough to accommodate the length of the wall anchor
(1-1/2"). Remove the Binder Nook. Install an anchor into each mounting
hole. Place the Binder Nook back into position, and insert a screw.
Note:
If floor trim prevents the unit from mounting flush to the wall,
we suggest the placement of a shim between the wall and the Binder
Nook Unit.
Thank you for purchasing our exclusive Store More Binder Nook
™
.
Before you begin, please refer to the Parts List to ensure that all materials
needed for assembly have been received. Please also read the Helpful Hints to
ensure assembly goes smoothly.
Locking Cam
Stud
Assembly Tool
HELPFUL HINTS:
• Check the direction of the arrows on each locking cam during assembly.
All arrows must point toward the small holes located on the outer edge of
the panels. (See diagram, right)
• All studs must be screwed in approximately 1/2" until the shoulder meets
the surface. To screw in studs use the assembly tool supplied or a straight
or Philips screwdriver.
PARTS LIST:
2-SHELF ADD-ON
Item# Description
Qty
6
Shelf
1
8A
Shelf 1
9
Left Side Panel
1
10
Right Side Panel
1
Bag of Hardware:
1
Locking Cams
14
Studs
14
Assembly Tool
1
Bag of Wall Mounting Hardware:
1
Screws
2
Decorative Plugs
2
Wall Anchors
2
2-SHELF BASE
Item# Description
Qty
3
Base Support
1
4
Shelf
1
5
Left Side Lower Panel
1
6
Shelf
1
7
Right Side Lower Panel
1
8
Shelf 1
Bag of Hardware:
1
Locking Cams
16
Studs
16
Assembly Tool
1
Bag of Wall Mounting Hardware:
1
Screws
2
Decorative Plugs
2
Wall Anchors
2
4-SHELF
Item# Description
Qty
2-Shelf Base Unit
1
2-Shelf Add-On Unit
1
6-SHELF
Item# Description
Qty
2-Shelf Base Unit
1
2-Shelf Add-On Unit
2
Pointed end of cross-slot
must be positioned
as shown
Completed
6-Shelf Unit
Completed
4-Shelf Unit
Item 8A
STORE MORE BINDER NOOK™ INSTRUCTIONS - 2, 4 and 6-Shelf Units
Helping Teachers Make A Difference
®
© 2007 Really Good Stuff
®
1-800-366-1920 www.reallygoodstuff.com
Made in Guangzhou, China
-0410
Helping Teachers Make A Difference
®
© 2007 Really Good Stuff
®
1-800-366-1920 www.reallygoodstuff.com
Made in Guangzhou, China
1
4
Rev. 4/10
Shelf Illustrations show markings
from both sides of shelves:
